Knowledge Of The Product And Preparation For Installation; Product Description And Intended Use; Components Used To Set Up Acomplete System - moovo TS4 Serie Instrucciones Y Advertencias Para La Instalación Y El Uso

Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 75

KNOWLEDGE OF THE PRODUCT AND PREPARATION FOR INSTALLATION

STEP 2
2.1 – PRODUCT DESCRIPTION AND INTENDED USE
In general, the series of devices that make up this product serve to auto-
mate a garage door for residential applications (fig. 1). This type may be
"sectional" or "up-and-over"; up-and-over doors may be projecting (dur-
ing opening the door protrudes outwards) or non-projecting with springs
or counterweights.
In particular, this kit is designed for the automation exclusively of sectional
garage doors. Therefore, to automate an up-and-over door, the special
oscillating arm must be fitted (mod. MA, not supplied in pack).
Any other use than as specified herein or in environmental condi-
tions other than as stated in STEP 3 is to be considered improper
and is strictly prohibited!
This product (TS432B - TS432Be - TS432BH - TS432BeH) comprises
an electromechanical gearmotor with a 24 V dc motor, a guide, chain and
a drive carriage. The gearmotor is also equipped with a control unit.
The control unit comprises an electronic board, a courtesy/indicator light
and a built-in radio receiver, plus an aerial, which receives the commands
sent by a transmitter.
The control unit can control different types of manoeuvres, each program-
mable and usable according to specific requirements.
Special functions are also available to enable personalisation of automa-
tion operation.
The automation is designed for use with various accessories which
enhance functionality and guarantee optimal safety. More specifically, the
control unit can memorise up to 150 keys of transmitters mod. MT4 and
up to 4 pairs of photocells, mod. MPQ.
The product is mains-powered, and, in the event of a power failure
enables manual movement of the door, by release of the drive carriage
using a special cord or by means of a release mechanism located exter-
nally (mod. MU, not supplied in pack).
In any event the door can also be opened by means of a buffer battery
(mod. ME, not supplied in pack) if fitted on the system.
SECTIONAL
1
2.2 – COMPONENTS USED TO SET UP A
COMPLETE SYSTEM
Fig. 2 illustrates all components used to set up a complete system, such
as that shown in fig. 8.
Some components shown in fig. 2 are optional and may not be
supplied in the pack.
List of components:
[a] - electromechanical gearmotor
[b] - guide for carriage in 3 parts + joining brackets
(only for mod. TS432B and TS432Be)
[c] - integral guide (only for mod. TS432BH and TS432BeH)
[d] - gearmotor ceiling mounting brackets
[e] - gearmotor wall-mounting brackets
[f] - mechanical stop for carriage travel limit
[g] - chain gear
[h] - drive chain
[i] - drive carriage
[l] - automation release knob and cord
[m]- door drive rod (for sectional doors only)
[n] - bracket for connection of drive rod to door
[o] - oscillating arm and relative drive rod
(mod. MA, for up-and-over doors only)
[p] - pair of photocells (wall-mounted) mod. MPQ
[q] - transmitter (portable) mod. MT4
[r] - radio control keypad mod. MKR (wall-mounted)
[s] - two buffer batteries mod. ME
(only for mod. TS432BH and TS432BeH)
[t] - Metal hardware (screws, washers, etc.)
[u] - external release kit mod. MU
(
*
) Note – The screws required for wall-fixture of components are not
included in the pack, as their type depends on the material and thickness
of the door in which they are inserted.
PROJECTING
WARNING!
*
NON-PROJECTING
English – 5
Tabla de contenido
loading

Este manual también es adecuado para:

Ts432km

Tabla de contenido