Preparing The Base Tool For Right-Angle And Straight - avdel Genesis G3 Manual De Instrucciones

All manuals and user guides at all-guides.com
A c c e s s o r i e s
Preparing the Base Tool for Right-Angle and Straight Swivel Head A t t a c h m e n t
•
Disconnect the air supply.
•
Remove any nose assembly items.
•
Remove Stem Collector Bottle Assembly
71210-20400.
•
Replace Stem Collector Bottle Assembly with
Safety Cap 71210-20201.
•
Unscrew Jaw Spreader Housing 41 and
remove with 'O' Ring 12, Locknut 40*, 'O'
Rings 19* and 15*, and Seal Housing 52*.
Do not refit these items (*).
•
Screw Stop Nut (71213-20200) onto the
front of Head Piston 36 as far as it will go, by
hand.
•
Fit Jaw Spreader Housing 41 and 'O' Ring 12,
tighten onto Head Piston 36, finally tighten
Stop Nut against Jaw Spreader Housing 41.
The tool is now ready to be fitted with a
swivel head, see page below.
Item numbers in bold refer to the General
Assembly drawing and Parts List on pages 24
and 25.
R I G H T- A N G L E S W I V E L H E A D c a p a b i l i t y
FASTENER
1
MATERIAL
NAME Ø
AVEX 1 / 8 3.2
® Aluminium Alloy
3.2
1 / 8 Steel
5 / 32 4.0 Aluminium Alloy
5 / 32 4.0 Steel
3 / 16 4.8 Aluminium Alloy
5 / 32 4.0 Aluminium Alloy
BULBEX ®
3 / 16 4.8 Aluminium Alloy
1 / 8 3.2 Stainless Steel
AVINOX II
®
5 / 32 4.0 Stainless Steel
–
® 4.0 Aluminium Alloy
AVSEAL II
– 4.0 Aluminium Alloy
– 5.0 Aluminium Alloy
– 5.0 Aluminium Alloy
1 / 8 3.2 Steel
STAVEX
®
5 / 32 4.0 Steel
1 / 8 3.2 Stainless Steel
5 / 32 4.0 Stainless Steel
1 2
In inches then in millimetres.
14
Base tool to receive a nose assembly
41 12 40 52
19
15
71213-20202
STOP NUT
Base tool to receive a swivel head
SWIVEL HEAD
PART Nº
PART Nº
07345-03600
07346-03000
07345-03700
07346-03100
07345-03700
07346-03100
07345-03800
07346-03200
07345-03800
07346-03200
07345-03700
07346-03100
07345-03800
07346-03200
07345-03700
07346-03100
07345-03800
07346-03200
71213-16401
71213-04000
71213-16402
71213-04700
71213-16403
71213-04100
71213-04800 71213-16404
07346-03100 07345-03700
07345-03800
07346-03200
07346-03100 07345-03700
07346-03200 07345-03800
B
Long nose tip for deep placing.
36
71210-20201
SAFETY CAP
NOSE TIP (mm) JAWS
'A' 'B' PART Nº
7.87 3.81 07340-00213
7.87 3.81 07340-00213
7.87 3.81 07340-00213
7.87 3.81 07490-04602
7.87 3.81 07490-04602
7.87 3.81 07340-00213
7.87 3.81 07490-04602
7.87 3.81 07340-00213
7.87 3.81 07490-04602
6.35 1.95 07340-00213
2
6.35 4.11 07340-00213
7.62 2.00 07340-00213
2
7.62 4.11 07340-00213
7.87 3.81 07340-00213
7.87 3.81 07490-04602
7.87 3.81 07340-00213
7.87 3.81 07490-04602
COMPLETE TOOL PART NUMBER :
A
precede with 71224-40
(the stop nut and safety cap are included)
IMPORTANT: in contrast to complete tools
with nose assemblies, those fitted with swivel
heads include the nose tip as a part of the head.
see
below
... 0 0 1
... 0 0 4
... 0 0 4
... 0 1 0
... 0 1 0
... 0 0 4
... 0 1 0
... 0 0 4
... 0 1 0
... 1 6 0
... 1 8 0
... 1 6 1
... 1 8 1
... 0 0 4
... 0 1 0
... 0 0 4
... 0 1 0