Before Starting The Equipment; Material Preparation - EINHELL TC-SY 18/60 Li Manual De Instrucciones Original

5. Before starting the equipment

Warning!
Always remove the battery pack before making
adjustments to the equipment.
5.1 Spray gun assembly (Fig. 2/3/4)
•
The trigger unit (14) is attached to the drive
unit (15) by a bayonet connector on the gun
mounting (7).
•
Open the locking lever (4).
•
Insert the trigger unit (14) into the gun moun-
ting (7) with a twist.
•
Close the locking lever.
•
Insert the material tube (11) into the material
tube connection (10)
•
Screw the container into the trigger unit.
5.2 Charging the Li battery pack (Fig. 16-17)
1. Remove the battery pack (d) from the handle,
pressing the pushlock button (c) downwards
to do so.
2. Check that your mains voltage is the same
as that marked on the rating plate. Insert the
power plug of the charger (e) into the mains
socket outlet.
3. The green LED will then begin to fl ash.
Push the battery pack onto the battery charger. In
section 12 (Charger indicator) you will fi nd a table
with an explanation of the LED indicator on the
charger.
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
Anl_TC_SY_18_60_Li_SPK13.indb 20 Anl_TC_SY_18_60_Li_SPK13.indb 20
GB
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
5.3 Battery capacity indicator (Fig. 16/Pos. b)
Press the button for the battery capacity indicator
(a). The battery capacity indicator (b) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too high. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
6. Operation
Warning!
Follow the safety precautions provided by the
manufacturer of the material you want to spray.
Use suitable face masks, gloves and protective
clothing.

6.1 Material preparation

The paint usually has to be thinned before it can
be used in the spray gun. Instructions on how to
thin the paint for spraying are not always printed
on the paint tin. You should use the viscosity table
as a guide (viscosity = consistency of the paint).
6.1.1 Measuring the viscosity (Fig. 5)
1. Mix the material thoroughly before measuring.
2. Completely immerse the viscosity cup (8) into
the material.
3. Then lift the viscosity cup (8) out of the mix-
ture and use a stopwatch to measure the time
it takes for all of the material to fl ow through
the cup. As soon as the continuous fl ow out
- 20 -
14.01.2021 13:35:45 14.01.2021 13:35:45