Replacing And Tightening The Belts; Maintenance, Inspection And Control; Starting Up And Using The Machine - Sima CEL-30 Manual De Instrucciones Original

3.2 REPLACING AND TIGHTENING THE BELTS

The machines leave the factory with the belts perfectly tightened. It is po ssible tha t due to the
incorrect mac hine installation o r lo ng use o f the ma chine, the be lts ge t lo ose. To ti ghten back t he b elt o r r eplace i t,
please consider the following steps (Fig.4).
1 Make sure the machine is unplugged off the power supply.
2 Remove the safeguard of the motor.
3 Loosen the tensor of the motor by means of the nuts A, B, C, and Fig.4
4 Replace or tighten the belt.
5 Once finished, proceed to the inverse.
6 Place the safeguard of the motor back.
Important: Never work with the motor safeguard while the transmission is removed, as this can
cause serious accidents.

3.3 MAINTENANCE, INSPECTION AND CONTROL

To keep the shear in good conditions, you need to check periodically the following points:
1 Check periodically (each 40 hours of use) the efficiency of the blades and if ne cessary to replace them,
proceed as per the instructions manual.
2 Check (monthly) the level of oi l with the visor B, Fig.5 y 5.1 and f ill up if the level is below the stopper A,
Fig.5 y 5.1. It is recommended to change the oil every two years.
TABLE OF OIL EQUIVALENCES ACCORDING TO MANUFACTURERS
Manufacturers
CEPSA
SHELL
ESSO
REPSOL
3 Grease (every 100 hours of use) the connecting rod by the nipple F, Fig. 5.1 with consistent grease. The
CEL-45 model has another point of lubrication with oil on top of the greasing of the connecting rod D, Fig. 5.1, which
needs to b e lu bricated w ith t he sa me o il that arrive s to the redu cer bo x, at this poin t of greas ing, we lubr icate the
bronze bearing.
4 Check the state and the tension of the transmission belts. The latter is supposed to be always tight to avoid
any sliding, which can cause a mal functioning of the machine.
5 All electrical or interior components installations are recommended to be effectuated by authorized people.
6 At the end of each day, unplug the machine.
7 If the machine is not covered, wrap it with impermeable cloth.
8 Clean periodically the visible parts of the machine and grease as necessary.
WARNING: Before performing any maintenance or cleaning, the power supply cable needs to be
unplugged.

4. STARTING UP AND USING THE MACHINE

WARNING: All safety reco mmendations must be followed, either the o nes mentioned in the present user manual or
those complying with all labour risks prevention norms in every location.
WHEELWORK: SIMA CEL models do no t need any wheelwork operations as they are specially designed to obtain the
maximum performance from start.
NORMAL USE OF THE MACHINE:
The e lectrical shear s have b een de signed to cu t flat and reinforc ed st eel bars for us e in t he s tructure and
other construction components is in conformity with all applicable provisions of the Directive of Machines (98/37/CE)
and th e na tional app licable regula tions
abnormal. Any tool or accessory added or amended without written authorization from the manufacturer is considered
inappropriate and dangerous. If any damage or injury is caused as a result thereof or by misuse of the machine, SIMA
S.A. exempts all responsibility as manufacturer. The machine must be installed on a plane, firm and horizontal surface
and the gro und shou ld not be sof t. T his machine DOES NOT HAVE TO BE USED UNDER THE RAIN. ALWAYS
WORK IN WELL ILLUMIINATED AREAS.
AUTEK MAQUINARIA 5392 7077
TYPE OF OIL
ENGRANAJE-HP 320
OMALA 320
SPARTAN EP-320
SUPERTAURO 320
.
Each o ther use tha t ha s no t bee n expre ssively i ndicated is co nsidered
AUTEK MAQUINARIA 5392 7077