Tabla de contenido
Idiomas disponibles
Idiomas disponibles
shoulder width apart. Distribute your weight
evenly on both feet.
(5) When ready to make a cut, push the lock-out
button completely in with the right thumb
and squeeze the trigger. This will turn saw on.
Releasing the trigger will turn the saw off. Make
sure the saw is running at full speed before
starting a cut.
(6) When starting a cut, slowly place moving chain
against the wood. The wood should be as close
to the saw body as possible. Hold saw firmly
in place to avoid possible bouncing or skating
(sideways movement) of saw.
(7) Guide the saw using light pressure and do not
put excessive force on the saw, letting the saw
do its work. The motor will overload and can burn
out. It will do the job better and safer at the rate
for which it was intended.
(8) Remove the saw from a cut with the saw running
at full speed. Stop the saw by releasing the on/off
switch. Make sure the chain has stopped before
setting the saw down.
(9) Keep practicing on scrap logs in a secure working
area until you are comfortable, using a fluid
motion and a steady cutting rate.
Kickback Safety Devices On This Saw
This saw has a low-kickback chain and reduced
kickback Guide Bar. Both items reduce the chance of
kickback. However, kickback can still occur with this
saw.
The following steps will reduce the risk of kickback.
•
Use both hands to grip saw while saw is running.
Use firm grip. Thumbs and fingers must wrap
around saw handles.
•
Keep all safety items in place on saw. Make sure
they work properly.
•
Do not overreach or cut above shoulder height.
•
Keep solid footing and balance at all times.
•
Stand slightly to the left side of saw. This keeps
your body from being in direct line with chain.
•
Do not let Guide Bar nose touch anything when
chain is moving.
•
Never try cutting through two logs at same time.
Only cut one log at a time.
•
Do not bury the Guide Bar nose or try plunge cut
(boring into wood using guide bar nose).
•
Watch for shifting of wood or other forces that
may pinch chain.
•
Use extreme caution when reentering a previous
cut.
•
Use only the low-kickback chain and guide
bar that were supplied with this Chainsaw or
recommended.
•
Never use a dull or loose chain. Keep chain sharp
with proper tension.
How to use Saw Safely
1. Use the Chainsaw only with secure footing.
2. Hold the Chainsaw at the right-hand side of your
body (See Fig. O).
3. The chain must be running at full speed before it
makes contact with the wood.
Cordless Chainsaw
4. Use the bumper spikes to secure the saw onto
the wood before starting to cut.
5. Use the Bumper Spikes as a leverage point while
cutting. (See Fig. P)
6. Do not operate the Chainsaw with arms fully
extended, attempt to saw areas which are difficult
to reach, or stand on a ladder while sawing (See
Fig. Q).
Never use the chainsaw above shoulder height
CUTTING WOOD UNDER TENSION (SEE FIG. R)
WARNING: When cutting a limb that is
under tension, use extreme caution. Be
alert for wood springing back. When wood
tension is released, limb could spring back and
strike operator causing severe injury or death.
When sawing logs supported on both ends, start
the cut from above(Y) about 1/3 of the diameter into
the log (overbuck) and then finish the cut (Z) from
below, in order to avoid contact of the chainsaw with
the ground. When sawing logs supported on only
one end, start the cut from below (Y) about 1/3 of
the diameter into the log (underbuck) and finish the
cut from above (Z) in order to avoid log splitting or
jamming of the chainsaw.
SAW MAINTENANCE
Follow maintenance instructions in this manual.
Proper cleaning of saw and chain and guide bar
maintenance can reduce chances of kickback. Inspect
and maintain saw after each use. This will increase the
service life of your saw.
Note: Even with proper sharpening, risk of kickback
can increase with each sharpening.
MAINTENANCE AND
STORAGE OF CHAINSAW
1. Remove the battery pack
•
When not in use
•
Before moving from one place to another
•
Before servicing
•
Before changing accessories or attachments, such
as saw chain and guard
2. Inspect chainsaw before and after each use.
Check saw closely if guard or other part has been
damaged. Check for any damage that may affect
operator safety or operation of saw. Check for
alignment or binding of moving parts. Check for
broken or damaged parts. Do not use chainsaw if
damage affects safety or operation. Have damage
repaired by authorized service center. To locate an
authorized service center, visit www.worx.com.
3. Maintain chainsaw with care.
•
Never expose saw to rain or direct moisture.
•
Keep chain sharp, clean, and lubricated for better
and safer performance.
•
Follow steps outlined in this manual to sharpen
chain.
•
Keep handles dry, clean, and free of oil and
17
EN
Tabla de contenido
