Tabla de contenido
Idiomas disponibles
Idiomas disponibles
EN
effective. On vertical surfaces,
apply the detergent starting at the
bottom and work your way
upward. This will prevent the
detergent from sliding down and
causing streaks. High pressure
rinsing should also progress from
the bottom to top. On particularly
tough stains, it may be necessary
to use a brush in combination
with detergents and high pressure
rinsing.
oPEraTion
The following cleaning procedure
will help you to organize your
cleaning task, and ensure that you
achieve the most beneficial results
in the shortest amount of time.
Remember to use the spraying/
cleaning techniques previously
listed.
SurfaCE PrEParaTion
Before starting a pressure wash
cleaning job, it is important to
prepare the surface that is to be
cleaned. This is done by cleaning
the area of furniture, and be sure
that all windows and doors are
closed tight.
In addition, you should make sure
that all plants and trees adjacent to
the cleaning area are protected by a
drop cloth.
This will ensure that your plants
won't be sprayed by the detergents.
iniTial high PrESSurE
rinSE
The next step is to spray the
cleaning surface with water to clear
off any dirt or grime that may have
collected on the surface.
This will allow your detergent to
attack the deep down dirt that has
worked its way into the cleaning
surface.
Before triggering the gun,
adjust the nozzle to a wide fan
pattern and slowly adjust to the
desired spray pattern. This will
help you avoid applying too much
concentrated
spray to the surface which could
cause damage.
uniTS wiTh dETErgEnT
aPPliCaTor
inCludEd
Follow manufacturer's label
directions for mixing correct
concentrations of detergent to water
ratio through the pressure washer,
which is approximately 5%
(1 to 20).
Unscrew to top of detergent
applicator and fill applicator with
detergent.
Replace top on applicator.
Apply detergent so it thoroughly
covers cleaning surface. Apply from
bottom to top to prevent detergent
from sliding down and streaking.
Allow detergent to remain on the
surface for a few minutes.
This is a good time to use a brush to
lightly scrub heavily soiled areas.
Never allow detergent to dry on the
cleaning surface.
Replace with the lance, or remove
applicator from end of lance.
Rinse detergent from surface.
noTE: Flush detergent applicator
with clear water following each use.
final rinSE
Start final rinse at bottom a work
upward.
Make sure you thoroughly rinse the
surface and that all detergent has
been removed.
ShuT down
Be sure all detergent is flushed from
system.
Turn off motor.
Turn off water supply.
After motor and water supply
are turned off, trigger gun to
depressurize system.
CauTion: Never turn water
supply off before turning motor off.
Serious damage could occur to the
pump andlor motor.
warning: Never disconnect
high pressure discharge hose
from machine while system is
pressurized.
To depressurize, turn motor off, turn
water supply off and squeeze gun
trigger 2-3 times.
After each use, wipe all surfaces of
the pressure washer with a clean,
damp cloth.
SToragE
Tips for extending the life of your
pressure washer:
Never operate unit without water.
Pressure washer is not supposed
to pump hot water.
Never connect to hot water
supply – this will significantly
reduce life of the pump.
Using detergent other than others
brand may cause damage to pump
components (o-rings, etc.).
This also applies to chemicals
such as bleach, dish soap, etc.
Never operate unit for more than
one (1) minute without spraying
water.
Resulted heat buildup will damage
pump.
Before adjusting nozzle's pressure
(high-to-low or low-to-high) release
trigger.
Failure to do so will reduce life of
o-rings in lance.
23
Tabla de contenido
