Tabla de contenido
Idiomas disponibles
Idiomas disponibles
10 • Connect the smoke stack wiring by plugging one into the other.
11 • Install the smoke stack as shown in the figure pushing it fully into place.
12 • Remove the cover from inside the engine.
13 • Click it onto the bodywork.
14 • Turn caboose upside-down. With black spacers against wheels, place axle
assembly into "V' slots and push down hard to secure.
15 • Attach the caboose lid by first inserting the right (longer) hinge tab into the
hinge hole (a). Then flex the lid by twisting it firmly to insert the left hinge tab
into its hole (b) and rotate the lid down to close it (c).
16 • To attach caboose to coal car, first remove plastic thumb nut and washer from
hitchpin.Then, place hitchpin into hole on hitchtab of coal car, replace washer
and thumb nut and tighten securely.
17 • To create a circular layout, assemble the curved rails as shown in the figure.
ATTENTION: you must position the train on the tracks so that it runs in a
clockwise direction.
18 • To create a oval track layout, add the 2 included straight rails (on opposite
sides). ATTENTION: you must position the train on the tracks so that it runs in
a clockwise direction.
19 • Remove the screw at the back of the seat.
20 • To remove the seat, press on the tab and
21 • Lift up on the seat.
22 • Plug battery terminal B into vehicle wiring terminal A.
23 • Reclose the seat back down by inserting the tabs into the two slots (see detail
into figure 23).
24 • Detail. NOTE: Always reclose and rescrew the seat.The train is now ready for use.
VEHICLE FEATURES AND INSTRUCTIONS FOR USE
25 • A: forward button. B: siren button.
OPTION
26 • OPTIONAL FIGURE-8 EXPANSION SET available. Circuit = 6 curves (plus 12
already supplied), 4 straight and 4 crossover.
REPLACING THE BATTERY
27 • Unscrew the seat safety screws. Lift up the seat. Unplug vehicle wiring
terminal A from battery terminal B, by pressing terminals on side and pulling
apart. Unscrew and remove battery fastener.
28 • Replace the battery. (NOTE:The replacement battery – separately available – is
a 6v/ 7Ah battery pack). Replace and screw back on the battery fastener.
Connect the two plugs. CAUTION:When you have finished, remember to close
and screw down the seat.
CHARGE BATTERY BEFORE USING.
BATTERY RECHARGE
WARNING:
WARNING: BATTERY CHARGING AND ANY OTHER
OPERATION ON THE ELECTRICAL SYSTEM MUST BE
CARRIED OUT BY ADULTS ONLY.
THE BATTERY CAN ALSO BE CHARGED WITHOUT REMOVING
IT FROM THE VEHICLE.
29 • Unplug vehicle wiring terminal A from battery terminal B, by pressing
terminals on side and pulling apart.
30 • Plug the battery charger terminal to a wall outlet following the instructions
enclosed. Connect the plug B to the battery charger plug C.
31 • Once the charge is completed unplug recharger from wall outlet. Unplug
recharger cord terminal C from battery terminal B.
32 • Plug battery terminal A into vehicle wiring terminal B.
33 • Close and fix the seat with the security screw.
BATTERY MAINTENANCE AND SAFETY
Before riding, charge your batteries for 18 hours to initiate them. Failure to do this
will result in permanent battery damage.
CAUTION:
Only adults should recharge batteries,never
children.
Never allow children to handle batteries.
Only use the batteries specified by the manufacturer.
Only use the charger specified by the manufacturer.
Do not mix old and new batteries.
Do not mix alkaline, standard (carbon-zinc), or rechargeable
(nickel-cadmium) batteries.
CHARGE BATTERY
• Charge the batteries no longer than 24 hours, following the instructions
enclosed with the battery charger.
• Charge the battery, as the vehicle shows low power, in this way you will avoid
damage to the battery.
• If you don't use your vehicle for a long period of time unplug the battery from
the main wire harness of the vehicle. Remember to charge the battery at least
every three months.
• Never charge the battery upside down.
• Do not forget batteries during charging! Check them periodically.
• Never use a replacement recharger or batteries unless they are approved by PEG
PEREGO.
• Do not mix old and new batteries.
• Batteries are sealed and maintenance free.
• Battery polarity must be observed when connecting battery to wiring.
WARNING:
• BATTERIES CONTAIN TOXIC AND CORROSIVE SUBSTANCES.
DO NOT TAMPER WITH THEM.
• Batteries contain an acid-based electrolyte.
• Do not make direct contact between battery terminals, as this can cause an
explosion or fire.
• Charging produces explosive gases. Charge batteries in a well ventilated area
away from sources of heat and flammable materials.
• Exhausted batteries are to be removed from the vehicle.
• Do not place the batteries near clothing to avoid damage.
IF A LEAK DEVELOPS
Shield your eyes. Avoid direct contact with the electrolyte, protect your hands.
Place battery in a plastic bag and follow directions listed below.
IF ELECTROLYTE COMES IN CONTAC WITH SKIN OR CLOTHING
Flush with cool water for at least 15 minutes.
See a physician at once.
IF ELECTROLYTE IS INGESTED
Give tap water, milk of magnesia or egg whites at once.
Do not induce vomiting.
See a physician at once.
DISPOSAL OF BATTERIES
Help protect the environment!
Do not throw used batteries in your regular, house hold trash.
Dispose of the old batteries in an approved dumping station; contact your local
environmental protection agency office for further information.
CAUTION AA BATTERIES
The insertion of batteries must only be carried out or supervised by adults. Do not
let children play with the batteries.
• The batteries should be replaced by an adult.
• Use only the type of battery specified by the manufacturer.
• Respect the polarity +/-
• Do not allow the batteries to be in contact with metal parts (risk of fire or
explosion).
• Always remove the batteries if the toy is not in use for a long period.
• Do not throw batteries on the fire.
• Never attempt to charge batteries that are not rechargeable.
• Remove dead batteries from the toy.
• Dispose of dead batteries into containers provided for the recycling of dead
batteries.
VEHICLE MAINTENANCE AND SAFETY
This product conforms to EN 71 and conforms to EN 50088 safety standard for
electric toys.
This vehicle is not intended for use on streets, around traffic or parked cars.
This product meets and/or exceeds all ASTM TOY SAFETY STANDARDS, including
F 963, Consumer Toy Safety Specifications.
MAINTENANCE AND CARE
• Regularly check the conditions of the vehicle, particularly the electrical system,
the plug connections, the covering caps and the charger. In case of fault, do not
try to use the vehicle and the charger. For repair use only original PEG PEREGO's
spare parts.
• PEG PEREGO assumes no liability if the electrical system is tampered with.
• Do not leave vehicle or batteries near sources of heat such as radiators, stoves,
fireplaces, etc.
• Protect vehicle from water, rain, snow, etc. Do not ride in loose sand or mud as
these substances will cause premature failure of switches, motors and gears.
• When operating in overload conditions, such as soft deep sand, mud or rough
uneven terrain, the overload circuit breaker will automatically disconnect the
power. After 10 or more seconds,the circuit breaker will automatically reset,
howevere you must eliminate overload conditions to resume normal driving.
• Periodically lubricate (with a light weight oil) moving parts, such as wheel
bearings, steering linkages, where they rotate or touch one another.
• The vehicle's surface can be cleaned with a dampcloth. Do not use abrasive
cleaners. The cleaning must be carried out by adults only.
• Never disassemble the vehicles mechanisms or motors unless authorized by
PEG PEREGO.
Conforms to EN 50088
Recargeable battery 6V 4,5Ah sealed lead-acid battery.
One 60W motor
Tabla de contenido
