Electrical Characteristics; Recommended Mounting Heights; Electrical Connection - Bobrick Trim Serie Instrucciones De Instalación

página de 15

/ 15
Contenido
Tabla de contenido

Tabla de contenido

Idiomas disponibles

model B-7120 White Painted steel cover and B-7128 stainless steel cover, 115V AC, 15 Amp, 1725 Watts, 50/60 Hz, Single Phase, cULus listed.

model B-7120 White Painted steel cover and B-7128 stainless steel cover, 208–240V AC, 6.8-7.8 Amp, 1400-1900 Watts, 50/60 Hz, Single

Phase; cULus listed, VDE and CCC approved, and CE marked.

Installation instructions and template provide information that will assist in the installation of the Bobrick B-7120 and B-7128 115V, B-7120 and B-7128

208-240V. Retain Installation Instruction Sheet for important maintenance instructions and warranty information.

Distance from floor to bottom mounting screw holes of mounting base.

Children's Washrooms, ages 3-4 ..............................................................................................................................................36''

Children's Washrooms, ages 5-8 ..............................................................................................................................................40''

Children's Washrooms, ages 9-12 ............................................................................................................................................44''

Universal Design ......................................................................................................................................................................48''

Bobrick automatic hand dryers should be installed at least 15" (380mm) above any projection or horizontal surface which may interfere with the

operation of the automatic sensor.

1. Start installation of dryer by

removing cover. Remove two

screws, from the bottom of the

dryer.

1. Hold the Installation Template against the wall in the desired location of

the installed dryer. See recommended mounting heights above.

2. Make sure line on template representing bottom of dryer mounting base

is horizontal and located at the desired height above floor.

3. Mark center of four mounting screw holes and hole for entry of electrical

wiring if electrical supply is concealed in wall and will enter dryer from

back through mounting base.

NOTE: Surface-mounted electrical supply entry is located in the lower right

corner of the mounting base. Surface-mounted supply cable should be

fitted in a conduit.

4. For brick, stone, and concrete walls drill four 0.315" (8mm) holes to suit

wall plugs 0.315" (8mm) x 1-1/4" (45mm) and screws#10 (4.8mm) x 2"

(50mm) long (provided). See template for wall plug and screw

installation details.

5. For plaster or dry wall construction, provide concealed backing to

comply with local building codes and secure with four #10 (M4.8) round-

head sheet-metal screws, or 3/16'' (5mm) toggle bolts (not furnished).

6. Fasten mounting base securely to wall.

THIs dryer Is InTended for connecTIon To fIXed WIrInG.

for ProPer eLecTrIcaL connecTIons, InsTaLLaTIon musT conform To LocaL BuILdInG code (usa), Iee reGuLaTIons (uK)

or LocaL reGuLaTIon (oTHer counTrIes).

Turn eLecTrIcaL PoWer suPPLy off Before maKInG eLecTrIcaL connecTIons.

dryer musT Be Grounded (earTHed).

unIT musT Be InsTaLLed By a QuaLIfIed LIcensed eLecTrIcIan.

THIs aPPLIance Is noT To Be used for domesTIc PurPoses BuT soLeLy In commercIaL PremIses.

THIs aPPLIance Is noT InTended for use By Persons (IncLudInG cHILdren) WITH reduced PHysIcaL, sensory or menTaL

caPaBILITIes, or LacK of eXPerIence and KnoWLedGe, unLess THey HaVe Been GIVen suPerVIsIon or InsTrucTIon

concernInG use of THe aPPLIance By a Person resPonsIBLe for THeIr safeTy.

cHILdren sHouLd Be suPerVIsed To ensure THaT THey do noT PLay WITH THe aPPLIance

1. Check that the electrical rating shown on the Dryer (rating label) is compatible with the electrical supply.

2. Connect dryer to nearest distribution panel. Use wire as required by local electrical code. In the United States and Canada use #14 wire.

Page 2