Electrical Characteristics; Recommended Mounting Heights; Electrical Connection - Bobrick CompacDryer B-710 Instrucciones De Instalación

Ocultar thumbs Ver también para CompacDryer B-710:

Instrucciones para instalación (15 páginas)

página de 13

/ 13
Contenido
Tabla de contenido

Tabla de contenido

Idiomas disponibles

model B-710,115V AC, 15 Amp, 1725 Watts, 60 HZ, Single Phase, cULus listed.

model B-710e, 220-240V, 7A, AC 1500-1700 Watts, 50/60 Hz, Single Phase; VDE approved, CE marked. B-710e is not available in the united

states and Canada.

Installation instructions and template provide information that will assist in the installation of the Bobrick B-710 115V, B-710E 220-240V. Retain

Installation Instruction Sheet for important maintenance instructions and warranty information.

Distance from floor to bottom mounting screw holes of mounting base.

Men's Washrooms ....................................................................................................................................................................46''

Women's Washrooms ...............................................................................................................................................................44''

Children's Washrooms, ages 3-9 .............................................................................................................................................32''

Children's Washrooms, ages 9-12 ............................................................................................................................................36''

Children's Washrooms, ages 12-15 ..........................................................................................................................................40''

Children's Washrooms, ages 15-18 ..........................................................................................................................................44''

Barrier-Free Design ..................................................................................................................................................................38''

Bobrick automatic hand dryers should be installed 15" (380mm) above any projection or horizontal surface which may interfere with the

operation of the automatic sensor.

1. Start installation of dryer by

removing cover. Remove three

screws, one from each side and

one from the bottom of the

dryer. Lift the cover from the

mounting base.

1. Hold the Installation Template against the wall in the desired location of the

installed dryer, see recommended mounting heights above.

2. Make sure line on template representing bottom of dryer mounting base is

horizontal and located at the desired height above floor.

3. Mark center of four mounting screw holes and hole for entry of electrical

wiring if electrical supply is concealed in wall and will enter dryer from back

through mounting base.

NOTE: Surface-mounted electrical supply entry is located in the lower right corner

of the mounting base. Bottom of mounting base has 1/2'' square (13mm) opening in

lower right corner to accommodate connection of electrical conduit.

4. Drill four holes for #10 (M4.8) mounting bolts or screws (not furnished).

5. For masonry walls provide four #10 expansion shields or anchors and secure

with four #10 (M4.8) sheet-metal screws (not furnished). For plaster or dry

wall construction, provide concealed backing to comply with local building

codes and secure with four #10 (M4.8) round-head sheet-metal screws, or

3/16'' (5mm) toggle bolts (not furnished).

NOTE: Use 2'' (50mm) long screws in top two mounting holes. Use 3'' (75mm) long

screws in lower two mounting holes.

6. Fasten mounting base securely to wall.

for proper eLeCtriCaL ConneCtions, CheCK LoCaL BuiLDinG CoDe. unit must Be instaLLeD By a quaLifieD LiCenseD

eLeCtriCian. WarninG: turn eLeCtriCaL poWer suppLy off Before maKinG eLeCtriCaL ConneC tions.

1. Connect dryer to nearest distribution panel. Use wire as required by local electrical code. In the United States and Canada use #12 wire.

2. Wiring Instructions:

a) A fused means for disconnection in all poles must be provided in the fixed wiring in accordance with the wiring rules.

b) Trim insulation from end of electrical wire.

c) Remove screws in strain relief clamp. Remove clamping crossbar. Feed electrical wire through clamp.

d) Make connection to terminal block as follows:

1) 115V: Connect ground (earthed) wire to ground (earthed) terminal marked

fitted with an earth (ground) wire.

2) Connect the black or Hot wire to terminal marked L1.

3) Connect the white or neutral wire to terminal marked N.

e) Replace crossbar on strain relief clamp. Tighten screws securing electrical wire.

NOTE: DEDICATED LINE IS REQUIRED FOR EACH 115 VOLT DRYER.

Page 2