Electrical Characteristics; Recommended Mounting Heights - Bobrick ECLIPSE B-740 Instrucciones De Instalación

Models B-740 (Vitreous enamel cover), B-748 (Chrome-plated cover), 115V AC, 20 Amp, 2300 Watts, 50/60Hz, Single Phase; cULus
Listed,.
Models B-740 (Vitreous enamel cover), B-748 (Chrome-plated cover), 208–240V AC, 9–10 Amp, 1900–2300 Watts, 50/60Hz, Single
Phase; cULus Listed, VDE approved, CE marked.
Distance from floor to bottom mounting screw holes of mounting base.
Men's Washrooms .............................................................................................................................................. 45-1/4''
Women's Washrooms ......................................................................................................................................... 43-1/4''
Children's Washrooms, ages 3-9 ....................................................................................................................... 31-1/4''
Children's Washrooms, ages 9-12 ...................................................................................................................... 35-1/4''
Children's Washrooms, ages 12-15 .................................................................................................................... 39-1/4''
Children's Washrooms, ages 15-18 .................................................................................................................... 43-1/4''
For the Handicapped .......................................................................................................................................... 37-1/4''
*
Bobrick automatic hand dryers should be installed 15" (380mm) above any projection or horizontal surface which may interfere with
the operation of the automatic sensor.
* Warm air hand dryer. Intended for use in a household environment by non-expert users. Not suitable for outdoor use.
** This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning
use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
*** If a fault develops disconnect the electrical supply, a qualified electrician should be called.
1. Start installation of dryer by removing cover. Loosen single
cover-locking screw located in recess in the air inlet/outlet grille
using a Phillips-head screwdriver.
FOR PROPER ELECTRICAL CONNECTIONS, CHECK LOCAL BUILDING CODE. UNIT MUST BE INSTALLED BY A QUALIFIED
LICENSED ELECTRICIAN
1. Hold the Installation Template against the wall in the desired location
of the installed dryer. See recommended mounting heights above.
2. Make sure line on template representing bottom of dryer mounting
base is horizontal and located at the desired height above floor.
3. Mark center of four mounting screw holes and hole for entry of
electrical wiring if electrical supply is concealed in wall and will enter
dryer from back through mounting base.
NOTE: Surface-mounted electrical supply entry is located in the lower
right corner of the mounting base. Surface-mounted supply cable should
be fitted in a conduit.
4. For brick, stone, and concrete walls drill four 0.315" (8mm) holes to
suit wall plugs 0.315" (8mm) x 1-1/4" (45mm) and screws#10
(4.8mm) x 2" (50mm) long (provided). See template for wall plug and
screw installation details.
5. For plaster or dry wall construction, provide concealed backing to
comply with local building codes and secure with four #10 (M4.8)
round-head sheet-metal screws, or 3/16'' (5mm) toggle bolts (not
furnished).
6. Fasten mounting base securely to wall.
2 Form No. 740-69 Multi Language

Electrical Characteristics

Recommended Mounting Heights

Important
Removal of Cover
Installation of Mounting Base
(Rev. 7/1/13) © 2013 Bobrick Washroom Equipment, Inc.
2. To remove cover, place a hand on each side of the cover and
tip the bottom away slightly from the air inlet/outlet grille. Lift
the cover upwards to release the top retaining bracket from the
mounting base.
7/8'' 22mm
Diameter Hole for
Between-Wall Wiring
5-11/16''
145mm
S
13/32'' 10mm
Dia. Hole for
Surface-Mounted Wiring
WARNING: TURN ELECTRICAL POWER SUPPLY OFF BEFORE
MAKING ELECTRICAL CONNECTIONS. DRYER MUST BE
GROUNDED (EARTHED).
(1150mm)
(1100mm)
(795mm)
(895mm)
(995mm)
(1100mm)
(945mm)
14-15/16''
379mm
C L
Mounting Base
3-1/8''
80mm
1-9/16''
40mm
Typ.
5-11/16''
145mm
S
S
Printed in U.S.A.
S
8-1/16''
205mm
C L