Battery Replacement - Elko EP SOU-2 Manual Del Usuario

Ocultar thumbs Ver también para SOU-2:
Tabla de contenido
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 57
Deleting of all programs
Auto
16--sep-- 10
PRG
in starting menu (time is shown
on display) - press simultaneously
button
and
and display
PRG
OK
announces a notice all
Reset
Auto
SOU-2
Performed by shortly pressing the hidden RESET button with a blunt-pointed object (e.g. a pencil
or screw-driver with a diameter of at most 2 mm).
The type of device and software version will be displayed for 1 second, then the device will enter
default mode. This means that the language is set to EN, all data is zeroed (light function, time/
date, user programs, device options function).
An example of SOU-2 programming
Settings for switching upon exceeding the range of 1,500 lux. Settings of hysteresis at 10% and off delay at 10 min. Upon a change of the lux switching range each Friday at 12:00 p.m. to 2,000 and
each Wednesday at 11:00 a.m. to 1,000 lux.
Auto
Prog
Prog
light
intensity
16--sep-- 10
PRG
OK
Prog
Prog
Prog
light
time prog
add
+ _
OK
Prog
Prog
Prog
day prog
hour
minute
OK
OK
+ _
Warning
Device is constructed for connection in 1-phase main alternating current voltage 230 V and
must be installed according to norms valid in the state of application. Connection according to
the details in this direction. Installation, connection, setting and servicing should be installed
by qualifi ed electrician staff only, who has learnt these instruction and functions of the device.
This device contains protection against overvoltage peaks and disturbancies in supply. For
correct function of the protection of this device there must be suitable protections of higher
degree (A, B, C) installed in front of them. According to standards elimination of disturbancies
must be ensured. Before installation the main switch must be in position "OFF" and the device
Prog
all
+
OK
OK
press button
to complete
OK
the deleting of all set programs
SOU-2
SOU-2
Prog
Prog
set (lux)
intensity
hysteresis
+ _
OK
OK
+ _
Prog
Prog
prog
day prog
hour
OK
OK
OK
Prog
Prog
Prog
on
Prog
Prog
OK
Prog
OK
OK
Prog
OK
OK
OK
OK
+ _

Battery replacement

You can change the battery without disassembling the device.
Auto
CAUTION
- only change the battery when the device is disconnected from power supply !!!
- the date and time must be reset after changing the battery !!!
- remove the plug-in module with the battery
- replace the original battery
- enter a new battery so that its upper edge (+) lines up with the plug-in module
- slide the plug-in module in the device and pay attention to polarity (+ up) – for roughly 1 s,
the display will show the name and the software version
- you can connect the device to power supply
Prog
Prog
Prog
set (%)
hysteresis
+ _
OK
OK
+ _
Prog
Prog
minute
Prog
OK
OK
Prog
+ _
OK
+ _
Prog
on
Prog
add
OK
OK
ESC
Prog
set (lux)
+ _
should be de-energized. Don´t install the device to sources of excessive electro-magnetic in-
terference. By correct installation ensure ideal air circulation so in case of permanent opera-
tion and higher ambient temperature the maximal operating temperature of the device is not
exceeded. For installation and setting use screw-driver cca 2 mm. The device is fully-electronic
- installation should be carried out according to this fact. Non-problematic function depends
also on the way of transportation, storing and handling. In case of any signs of destruction,
deformation, non-function or missing part, don´t install and claim at your seller it is possible to
dismount the device after its lifetime, recycle, or store in protective dump.
7 / 7
Prog
Prog
delay
OK
OK
+ _
+ _
Prog
on
Prog
Prog
Prog
on
Prog
OK
Prog
OK
OK
Prog
set (lux)
OK
OK
OK
+ _
Auto
16--sep-- 10
+
CR2032
Prog
Prog
Prog
delay
OK
OK
ESC
Prog
Prog
add
prog
OK
OK
OK
- long press (>1s)
- short press (<1s)
Tabla de contenido
loading

Tabla de contenido