Important Information - Product Care; Fitting And Removing The Battery Pack; Plug Pack Charger Assy; Assy - I-DRILL 2i-drill Manual Del Usuario

Important information – Product care
This drill/driver uses Lithium Ion Battery Cells. Care
MUST be taken to ensure both the safety and life of the
pack is maintained. Ensure you have read all of the safety
notes in the previous pages before using the drill/driver.
Treat the battery pack with care and within the guidelines
of this manual. If the pack does become immersed in water
or any fluids, or is subject to a sever drop etc, or it does not
GB
operate within the guidelines of this manual, immediately
STOP using the battery pack and have it checked.
During operation avoid overloading the drill/driver. If
the drill driver is overloaded it will automatically STOP.
Overloading may occur for a number of reasons including
when the drill driver is pushed too hard or when using a
drill bit or attachment greater than what is specified. If you
do overload the drill driver during operation refer to the
"Overload" section in this manual.
Note: When the battery of the drill is at the lower end of the
charge, the drill is more susceptible to the overload condition.
Running the drill at close to maximum load, or continual
resetting of the overload will cause the battery pack to
over heat. When a preset cell temperature is detected, the
battery pack will automatically STOP operating and will not
restart until the battery pack has cooled to a safe level.
In this condition, DO NOT force cool the pack by placing in
a freezer or similar device. Refer to the "Overload" section
in this manual.
Another feature of the drill/battery pack is the low voltage
cut out feature. This feature operates when the voltage
drops below a pre set value. When this occurs the tool will
automatically stop operating. To correct the situation you
need to either insert another charged battery into the drill
or recharge the existing battery, and then proceed with the
drilling/driving application.
Note:
Attempting to restart the tool in this condition without
either recharging the battery or installing a battery with
charge will lead to drill restarting and then stopping again
after only a few seconds of operation.
These safety devices have been fitted for the safety,
reliability and life of the tool.
Fitting and removing
the battery pack.
To remove the battery pack from
the drill, press the two side tabs
on the battery pack firmly and
pull the pack from the drill.
To fit the battery pack into the
drill, orientate the battery pack so
the side tabs of the battery pack
are on the left and right side of
the drill, and the high trim section
of the pack is forward. Enter the
pack into the drill aligning the ribs
of the pack with the inner ribs of
the drill. Push the battery pack
all the way into the drill handle
without forcing. The side tabs will
"Click" into place preventing the
pack falling out.
To fit the battery pack into the
charger, Orientate the battery
so the side tabs of the battery
are to the sides of the charger
and the high side of the battery
trim is towards the charger base
indicators. Align the ribs of the
battery pack with the ribs of the
charger base recess and insert
the battery all the way into the
charger. The side tabs are not
used.
To remove the battery pack from
the charger base, lift the battery
from the charger base without
the need to depress the battery
pack tabs.
12

Plug pack charger assy

The plug pack charger is designed to operate on voltages
between 100Volts and 240Volts AC, 50 or 60Hz.
The only requirement is to fit the required pin insert into the
plug pack charger.
The plug pack charger consists of the charger housing and
4 clip on plug configurations.
WARNING
DO NOT
attempt to use the charger without fitting one of
the supplied clip on pin moldings.
DO NOT insert the clip on moldings into ANY general
power outlet without FIRST attaching to the charger plug
pack housing.

Assy

Select the pin configuration
attachment to suit the general
power outlet to be used.
Orientate the pin attachment so
the rear of the molding aligns
with the recess in the plug pack
housing. The attachment will
only assemble one way. When
aligned, insert the pin attachment
fully and the insert "Clicks" into
place. CHECK the insert is
locked in place.
To remove the pin attachment
insert, press and slide down the
small release button and pull
the insert from the plug pack
charger.

Battery charging

IMPORTANT. Before attempting to charge the battery,
check the charger, the charger base and the battery
to ensure the charging equipment matches the battery
supplied. The components are all labelled with
component numbers.
CAUTION! The rechargeable battery is not fully charged on
leaving the factory. Charge the rechargeable battery before
first use.
CAUTION! The working temperature of the charger is 0
degree to 45 degrees (32 degree f to 115 degree f).
CAUTION!
When recharging the battery, connect the plug
pack charger into the charger base, then connect the plug
pack charger to the power source. The battery should be
inserted last.
1. Assemble the plug pack charger with the required pin
configuration. Connect the plug pack charger to the
charger base, and then plug in the plug pack charger into
the mains supply and turn on. The green LED will display.
2. Insert the rechargeable battery into the charger base (6).
The red LED will light and the same time the green one
will turn off.
3. The charging process will last approx. 45 - 60 min and
be displayed by red permanent lighting of the LED. The
charge will be completed when the red LED goes out and
the green LED lights up.
4. During the charging process
the battery drill screwdriver
can be placed down on the
drill support (10). The drill
support can be used either
clipped to the charger base or
separated to the charger base
by simply unclipping to detach.
13
GB