Routine Maintenance; General Information; Refuelling; Check/Top-Up Engine Oil - Stiga MP2 504 Manual De Instrucciones

7.

ROUTINE MAINTENANCE

7.1

GENERAL INFORMATION

The safety regulations to follow are
described in chap. 2. Strictly comply with these
instructions to avoid serious risks or hazards.
Before conducting any inspections, cleaning or
maintenance/adjustment interventions on the machine:
• stop the engine;
• make sure that all moving parts have
come to a complete stop;
• wait until the engine is sufficiently cold;
• remove the spark plug cap;
• read the relevant instructions;
• Use suitable clothing, protective gloves and goggles.
• The frequency and types of maintenance are summarised
in the "Maintenance Table". The table will help you
maintain your machine's safety and performance.
It lists the main maintenance tasks and how often
they need to be performed. Carry out the relevant
task as soon as it is scheduled to be performed.
• The use of non-genuine and/or incorrectly
assembled spare parts and attachments could
adversely affect machine operation and safety. The
manufacturer shall decline all liability in the event
of injuries or damages caused by such parts.
• Genuine spare parts are supplied by authorized
assistance workshops and dealers.
IMPORTANT All the maintenance and adjustment
operations not described herein must be carried out
by your dealer or Authorised Service Centre.
7.2

REFUELLING

To refuel:
1. Unscrew the tank closure cap and remove it ..
2. Insert a funnel.
3. Refuel and remove the funnel.
4. Close the fuel cap securely after refuelling
and clean away any spills.
NOTE Do not fill the fuel tank right to the top.
IMPORTANT Do not drip petrol onto the plastic parts of
the engine or the machine to prevent damaging them and
remove all traces of spilled petrol immediately. The warranty
does not cover damage to plastic parts caused by petrol.
NOTE Fuel is perishable and should not remain
in the tank for more than 30 days. Before storing for
a long period, fill the tank with a sufficient amount
of fuel to reach final destination (chap. 9).
7.3

CHECK/TOP-UP ENGINE OIL

To ensure that the machine will function properly
over time, it is highly recommended to change
the engine oil regularly, following the timing
indicated in the engine's Instruction Manual.
All manuals and user guides at all-guides.com
The oil can be discharged at a specialised servicing centre,
or by using a syringe to suction the oil out through the filler
spout, bearing in mind you may need to repeat the operation
several times in order to completely empty the tank.
Remember to top-up with oil before using the machine again.
Procedure:
• Position the machine on a level surface for the check.
• Wipe around the dipstick. Unscrew it and
• Push the dipstick down completely
• Now pull the dipstick up again. Read off the oil level.
• Top up if the level is lower than the "MAX" mark .
overheat. If the oil level exceeds the "MAX" mark, the
oil must be drained until the correct level is achieved.
Clean thoroughly following the instructions
below every time it is used.
• Accurately wash the machine with water after each
• Paint on internal chassis parts may come off over
• Always make sure the air intakes are free of debris.
• Do not use aggressive liquids to clean the chassis.
• To reduce fire hazards, keep the lawnmower
• If accessing the lower part is necessary, only tilt the
Remove the grass-catcher;
1.
2.
3.
4.
1.
2.
EN - 9
7.3.1 Check/top-up
pull it out. Wipe the dipstick clean.
without screwing it into place.
Do not overfill as this could cause the engine to
7.4

CLEANING

7.4.1 Cleaning the machine
mowing, remove grass debris and mud accumulated
under the chassis to prevent it from drying and causing
problems the next time the lawnmower is used.
For side and rear discharge: if fitted,
remove the discharge chute.
time due to the abrasive action of cut grass; if this
happens, promptly touch-up paint with rust-proof paint
to prevent rusting that could corrode the metal.
and, in particular, the engine free of grass,
leaves, or excessive grease.
machine on the side indicated in the engine manual,
following the relevant instructions, making sure that
the machine is perfectly stable before performing any
interventions. On side discharge models, remove
the discharge chute (if installed - see 6.1.2.d).
7.4.2 Cleaning the interior
Connect the water hose to the specific
attachment (fig. 20.A);
Lower the cutting height as far as possible;
Always stand behind the lawnmower handle;
Start the engine.
7.4.3 Cleaning the grass-catcher
Empty the grass catcher;
Shake it to remove grass cuttings and soil residue;