Technical Data - Martin Yale MY 3000SC Instrucciones De Uso

GB
fig. 3
MATERIAL JAM IN MACHINE:
(Auto-reverse-function)
If too much material is fed in, causing a jam, the
machine will respond as follows:
- Cutting mechanism halts, then runs one step in
reverse (material will be released) and stops.
- The motor shuts down automatically.
- The pilot lamp (5) (fig. 1) lights up.
Proceed as follows:
Paper jam in the paper feed slot (9)
- Tear off the returned paper just above the feed
slot.
- Briefly move the rocker switch (1) (fig. 1) to the
" " position.
- The pilot lamp (5) (fig. 1) goes out.
- The cutting system then runs forward and shreds
the paper remaining in the cutter.
- Continue shredding, feeding smaller quantities
of paper.
Material jam in the security feed slot (10)
- Remove the returned material.
Take care when removing material
as sharp edges may cause injury.
- Briefly move the rocker switch (1) (fig. 1) to the
" " position.
- The pilot lamp (5) (fig. 1) goes out.
- The remaining material to be shredded is then
fed to the cutting system again.
- Once the remaining material has been shredded,
continue shredding, feeding the correct
quantities.
Description
Lubricant, 125 ml bottle
Note: For orders of special accessories and spare parts, please contact your dealer.
All manuals and user guides at all-guides.com
OPERATION
EMPTYING THE RECEPTACLE (Fig. 3):
Proceed as follows:
- Remove the receptacle from in front of the
machine and empty its contents. Pilot lamp
lights up (7) (fig. 1).
- Replace the empty receptacle under the machine
and push all the way to the back.
11
Note: The machine will only run when the
receptacle is pushed completely under the
machine.
MALFUNCTIONS
- If necessary, move the cutting system manually
to and fro between forward and reverse running
until all the material has been fed through and
shredded.
Wait each time until the motor stops
before switching direction.
MOTOR PROTECTION:
The motor shuts down automatically, should it
become overloaded. The pilot lamp (6) (fig. 1)
lights up. Turn the machine off with the pushbutton
switch (1) (fig. 1).
Allow the motor to cool down for 20 to 25 minutes
(depending upon room temperature) and then
continue shredding.
CHECKLIST IN CASE OF MALFUNCTIONS:
If the device does not function, check the following:
- Is the plug connected to the mains?
- Is the pushbutton switch (1) on?
- is the receptacle placed properly under the
machine?
- is the receptacle full?
The receptacle has to be emptied.
- is there a material jam in the machine?
Follow the instructions under "MATERIAL JAM"
- has the motor been overloaded?
Wait until the motor has cooled, and then restart.
If none of the above applies, please contact
your dealer.
ACCESSORIES
CLEANING THE PHOTOCELLS (fig. 4):
If paper particles should come to rest in the inlet
guide (for example after a paper jam) it is possible
that the machine will not turn off, due to the broken
light barrier.
To remove these paper strips and also to clean
the photocell, pass another sheet of paper through
the feed slot, or switch the machine to reverse and
wipe both „eyes" of the photocell with a brush.
MAINTENANCE
CUTTING BLOCK (3.8x48 mm)::
After approximately 15 minutes of continuous
operation, switch to reverse running for about 15-
20 seconds and during this time spray some of the
special oil on to the cutting mechanism (refer to
"ACCESSORIES" for the order number).
TIP FOR ENERGY SAVING:
Please make sure that the shredder is switched
off over night (pushbutton switch (1) (fig. 1).
Cutting width:
MY3000SC:
MY3000CC:
Cutting capacity paper:
MY3000SC:
MY3000CC:
Cutting capacity
Credit cards/CD's/DVD's:
Supply voltage:
Pre-fusing:
Noise level:
Power:
Dimensions:
Width:
Depth:
Order-No.
Height:
99943
Weight:
5
MY 3000 SC
MY 3000 CC
MAINTENANCE
3
fig. 4

TECHNICAL DATA

4 mm
3.8x42 mm
20-22 sheets (70g/m
13-16 sheets (70g/m
feed one at a time
230V/50Hz
240V/50Hz
120V/60Hz
100V/50/60Hz
10 amps (slow-blow)
approx. 63 dB(A)
0.7 kW
420 mm
340 mm
660 mm
ca. 15kg
2 )
2
)