Features; Technical Data - Surtek COMP410 Manual Del Usuario

ing parts, do not operate the compressor with
the safety shield removed. Allow hot parts to
cool before handling or servicing.
• Do not operate the electric tool without in-
stalled guards. Please note that the compressor
will start automatically when the pressure falls
off to minimum! Disconnect from power supply
prior to any servicing.
Ensure that when switching on (e.g. after servic-
ing) no tools or loose parts are in the electric tool.
• Be certain to read all the labels on the contain-
ers of paint or other materials to be sprayed.
• Always wear safety goggles or glasses when us-
ing the air compressor.
• Do not attempt to adjust the pressure switch
or the release valve located under the pressure
switch cover.
• Drain the moisture from the tank daily. It will
help prevent corrosion.
• Pull the ring on the safety valve daily to ensure
that it operating properly and to clear any pos-
sible instructions.
• Keep the compressor at least 3 m from the
nearest wall to ensure adequate ventilation for
cooling purposes.
• Before transporting the compressor make sure
that the pressurised air is bled from the tank and
that the compressor is firmly secured.
• Protect the air hose and cord set from damage.
Inspect for weak or worn spots regularly and re-
place if necessary.
• Do not use an extension cord with this product.
Use additional air hose instead of an extension
cord to prevent power loss and possible damage
to the motor. Use of an extension cord voids the
warranty.
• After long working periods external metal
parts could be hot.
• Always press the on/off button down to switch
off the compressor before switching off the pow-
er or removing the power plug.
• Do not use the compressor without first check-
ing the oil level. It must be close to the red circle
as viewed on the oil gauge.
NOTE: the compressor is supplied without oil. It
must be filled before the first use.
• After using the compressor, switch off the on/
off button, disconnect the power supply and
open the outlet valve to release the pressure.
• Do not attempt to remove any part of the ma-
chine whilst is under pressure.
• Ensure that the lubricating oil is clean and that
the oil level is maintained at the correct level.
Replace the oil as indicated in the Maintenance
section of this manual.
• Never apply the outlet air of this compressor
E N G L I S H •
directly on to any part of a person's body. Do not
attempt to block the air outlet with your finger
or any part of your body.
WARNING: in the event that an air line is cut
or broken, the air supply must be turned off at
the compressor. A broken air line which is not
supported is extremely dangerous and can whip
around very quickly, both with the capability of
striking people, and blowing foreign particles
into the air.

FEATURES

KNOW YOUR TOOL
Before attempting to use this product, become
familiar with all of its operating features and
safety requirements.
3
1
4
1. TANK.
2. CRANKCASE VALVE.
3. AIR FILTER.
4. WHEELS.
5. HUMIDITY DRAIN VALVE.

TECHNICAL DATA

COMP410
VOLTAGE-FREQUENCY
MAXIMUM CURRENT
TANK CAPACITY
MAXIMUM FLOW
MAXIMUM PRESSURE
NO LOAD SPEED
POWER
HOUUS OF MAXIMUM USE
NOISE LEVEL
WORKING TEMEPERATURE
WEIGHT
COMP425B
VOLTAJE-FRECUENCIA
CORRIENTE MÁXIMA
CAPACIDAD DEL TANQUE
CAUDAL MÁXIMO
PRESIÓN MÁXIMA
VELOCIDAD EN VACÍO
POTENCIA
HORAS DE USO MÁXIMO
NIVEL DE RUIDO
TEMPERATURA DE TRABAJO
PESO
U s er 's M an u al
2
5
127 V ~ 60 Hz
8 A
10 L
150 L/min (5,3 CFM)
115 PSI
3 450 r/min
1,5 HP
6 hours
88 dB
85 °C - 90 °C
14,2 kg (31,3 lb)
127 V ~ 60 Hz
12,5 A
25 L
224 L/min (7,9 CFM)
115 PSI
3 450 r/min
2 HP
6 hours
88 dB
85 °C - 90 °C
21,4 kg (47,1 lb)
13