Ingersoll Rand 77A–EU Serie Manual Del Usario

Ingersoll Rand 77A–EU Serie Manual Del Usario

Ocultar thumbs Ver también para 77A–EU Serie:
Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 21

Enlaces rápidos

TPD1399
AIR ANGLE GRINDERS, SANDERS AND POLISHERS
Series 77A–EU Air Angle Grinders, Sanders and Polishers are designed for smoothing,
trimming or removing metal in close–quarter areas in foundries, shipyards, steel mills and in
construction applications.
Ingersoll–Rand is not responsible for customer modification of tools for applications on which
Ingersoll–Rand was not consulted.
IT IS THE RESPONSIBILITY OF THE EMPLOYER TO PLACE THE INFORMATION
IN THIS MANUAL INTO THE HANDS OF THE OPERATOR.
FAILURE TO OBSERVE THE FOLLOWING WARNINGS COULD RESULT IN INJURY.
PLACING TOOL IN SERVICE
Always operate, inspect and maintain this tool in
accordance with all regulations (local, state, federal
and country), that may apply to hand held/hand
operated pneumatic tools.
For safety, top performance, and maximum durability
of parts, operate this tool at 90 psig (6.2 bar/620 kPa)
maximum air pressure at the inlet with 1/2" (13 mm)
inside diameter air supply hose.
Always turn off the air supply and disconnect the air
supply hose before installing, removing or adjusting
any accessory on this tool, or before performing any
maintenance on this tool.
Do not use damaged, frayed or deteriorated air hoses
and fittings.
Be sure all hoses and fittings are the correct size and
are tightly secured. See Dwg. TPD905–1 for a typical
piping arrangement.
Always use clean, dry air at 90 psig maximum air
pressure. Dust, corrosive fumes and/or excessive
moisture can ruin the motor of an air tool.
Do not lubricate tools with flammable or volatile
liquids such as kerosene, diesel or jet fuel.
Do not remove any labels. Replace any damaged label.
The use of other than genuine Ingersoll–Rand replacement parts may result in safety hazards, decreased tool performance, and
increased maintenance, and may invalidate all warranties.
Repairs should be made only by authorized trained personnel. Consult your nearest Ingersoll–Rand Authorized Servicenter.
Refer All Communications to the Nearest
Ingersoll–Rand Office or Distributor.
 Ingersoll–Rand Company 1999
Printed in U.S.A.
INSTRUCTIONS FOR SERIES 77A–EU
IMPORTANT SAFETY INFORMATION ENCLOSED.
READ THIS MANUAL BEFORE OPERATING TOOL.
03530680
USING THE TOOL
Always wear eye protection when operating or
performing maintenance on this tool.
Always wear hearing protection when operating this
tool.
Keep hands, loose clothing and long hair away from
rotating end of tool.
Anticipate and be alert for sudden changes in motion
during start up and operation of any power tool.
Keep body stance balanced and firm. Do not
overreach when operating this tool. High reaction
torques can occur at or below the recommended air
pressure.
Tool accessories may continue to rotate briefly after
throttle is released.
Air powered tools can vibrate in use. Vibration,
repetitive motions or uncomfortable positions may be
harmful to your hands and arms. Stop using any tool
if discomfort, tingling feeling or pain occurs. Seek
medical advice before resuming use.
Use accessories recommended by Ingersoll–Rand.
This tool is not designed for working in explosive
atmospheres.
This tool is not insulated against electric shock.
Form P6523–EU
GB
Edition 12
October, 1999
Tabla de contenido
loading

Resumen de contenidos para Ingersoll Rand 77A–EU Serie

  • Página 21: Pulidoras, Amoladoras Angulares Neumaticas Odelo 77A-Eu

    03530680 Impreso P6523–EU Edición 12 Octubre, 1999 INSTRUCCIONES PARA LIJADORAS Y PULIDORAS, AMOLADORAS ANGULARES TPD1399 NEUMATICAS ODELO 77A–EU NOTA Las Lijadoras y Pulidoras , Amoladoras Angulares Neumáticas Serie 77A–EU están diseñadas para pulido, recorte o eliminación de metal en fundiciones, astilleros, fábricas de acero y en la industria de construcción.
  • Página 22: Etiquetas De Aviso

    ETIQUETAS DE AVISO AVISO EL HACER CASO OMISO DE LOS AVISOS SIGUIENTES PODRIA OCASIONAR LESIONES. ADVERTENCIA ADVERTENCIA ADVERTENCIA Cortar siempre el suministro Use siempre protección ocular de aire y desconectar la man- Use siempre protección para guera de suministro de aire cuando utilice esta herramienta los oídos cuando utilice esta o realice operaciones de...
  • Página 23: Avisos Especificos De Lijadora/Pulidora

    AVISOS ESPECIFICOS DE LIJADORA/PULIDORA • Estas Lijadoras y Pulidoras funcionarán a la No use nunca un accesorio que tenga una máxima velocidad constante especificada en la placa de velocidad de funcionamiento menor a la velocidad de identificación si la línea de suministro de aire a la la Lijadora o Pulidora en la que se va a usar.
  • Página 24: Especificaciones

    PARA PONER LA HERRAMIENTA EN SERVICIO ESPECIFICACIONES ♦Nivel de HNivel de Sonido Modelo Velocidad Muela Tipo 27 y 28 Eje y Constante Cubremuela dB (A) Vibraciones •Potencia pulgadas Presión 77A60P107M–EU 6.000 5/8–11, 7” 85,9 98,9 77A60P109M–EU 6.000 5/8–11, 9” 85,9 98,9 77A75P107M–EU 7.500...
  • Página 25: Declaracion De Conformidad

    DECLARACION DE CONFORMIDAD Ingersoll–Rand, Co. os abajo firmantes (nombre del proveedor) Swan Lane, Hindley Green, Wigan WN2 4EZ (domicilio) Declaramos que, bajo nuestra responsabilidad exclusiva, el producto: Lijadoras y Pulidoras, Amoladoras Angulares Neumaticas Modelo 77A–EU a los que se refiere la presente declaración, cumplen con todo lo establecido en las directivas: 98/37/CE ISO8662, PNEUROP PN8NTC1...
  • Página 31 Service Centers Centres d’entretien Niederlassungen Centri di Assistenza Centros de Servicio Service Centra Ingersoll–Rand Company Ingersoll–Rand Nederland Produktieweg 10 510 Hester Drive 2382 PB Zoeterwoude White House Nederland TN 37188 Tel: (31) 71 452200 Fax: (31) 71 5218671 Tel: (615) 672 0321 Fax: (615) 672 0801 Ingersoll–Rand Company SA PO Box 3720...

Tabla de contenido