GYS Gyspot COMBI 230 Manual Del Usuario página 8

VIII/ STEEL DENT PULLER DESCRIPTION :
Front panel (same as Gyspot 3502S Panel)
Power indicator
Used tool indicator
Keys + and – to select
the tool and adjust power
level.
IX / USE :
Starting and adjustment :
Connect the machine to an adapted power supply and press the « ON/OFF » key. The indicators switch on for few seconds then the machine
displays :
Tool n°1 (stars welding or use of dent-pulling gun).
-
Power level 5 (Default : setting adapted for steel sheet 0.8mm).
-
To change the power level, press the keys + or -. By keeping pressed one of these keys, the power level will appear automatically.
The power levels suggested make it possible to rectify variable sheets thickness.
Level L 1
Sheet 0,3mm 0,4mm
steel
thickness
To change the tool used at top of the gun, press the key
During this time, it is possible to change the tool number by pressing on keys + or - .
To stop the blinking before the end of 5 seconds press again the key
The different tools suggested make it possible to do the following works :
Tool 1 : Panel withdrawl using a hammer, stars
or dent-pulling clamp.
Tool 2 : small repair or welding of nails for
withdrawl works
Tool 3 : Lowering of impacts with specific end
copper.
Tool 4 : Carbon electrode for panel shrink.
System of automatic starting:
The machine provides a system of automatic starting that automatically generates a welding spot.
To carry out a spot, proceed as follows :
Connect the earth clamp of the generator to the metal panel to be rectified following the below instructions:
Fix the earth clamp as near the place to be welded as possible.
Do not connect it to an another panel (Example: do not connect the earth point on a door to rectify the vehicle wing)
Pickle properly the sheet at the place of connection.
Pickle the place where the sheet must be worked.
Fix on the gun one of the tools provided by tightening the nut located at the top of the gun.
Select the tool and the power (see starting and adjustment).
Put in contact the tool of the gun with the sheet to be welded.
The generator will detect automatically the electrical contact and will generate a welding spot within less than 1 second.
To weld a 2nd spot, it is necessary to break the contact between the gun and the panel during at least ½ second and then establish a
new contact.
Thermal protection of the generator :
The machine is provided with an automatic thermal protection system. This system stop the use of the machine during a few minutes in
case of too intensive use. In this case, the yellow indicator of thermal defect is on.
Gracias para su elección ! Antes de toda utilización o mantenimiento, leer con una atención particular las notas indicadas abajo en lo que
concierne las normas de seguridad, de manera a evitar accidentes a los obreros o deteriorar la instalación de soldadura.
CONFORMITY CERTIFICATE :
GYS Company attests under its own responsibility that product: GYSPOT COMBI 230 is manufactured according to the requirements of the
following European directives :
Low voltage directive: 2006/95/EC - EMC directive : 2004/108/EC - Machinery directive : 2006/42/EC
-
They are in conformity with the harmonized standards:
EN50063 & EN 62135-2 1 EN 60204-1
-
EC marking date: Septembre 2009.
08/10/09
S.A.S. GYS
134 BD des Loges
53941 Saint Berthevin
FRANCE
GYSPOT COMBI 230
SETTINGS AS AN INDICATION
2 3 4
0,5mm 0,6mm 0,7mm
. The indicator of tool number starts blinking for 5 seconds.
Nicolas BOUYGUES
Chief Executive Officer
5 6 7
0,8mm 0,9mm 1mm
Tool 5 : Welding of rivets with a specific end coppers
for side mouldings
Tool 6 : Welding of nails with a specific end coppers
for ground cable fixing
Tool 7 : Welding of pins with a specific end coppers
for fixing vehicle ground cable and electrical network
Yellow indicator of
thermal protection
Starting « ON/OFF »
Switch.
Tool selection for the
steel dent pulling gun.
8 9 10
1,1mm 1,2mm 1,3mm
8