Cleaning & Maintenance - Bosch Sensi Serie Instrucciones De Uso

Automatic clean warning
Pilot light (11) will flash indicating that boiler must be
rinsed.
1. Check carefully that the appliance is cold and
r
unplugged for more than 2 hours, and that the water
tank (1) is empty.
2. Fix the iron to the stand by inserting the tip of the iron
r
into the front slot and moving the fixation lever (13)
against the heel of the iron.
3. Place your appliance over a sink or bucket.
4. Lean the appliance on the opposite side of the filter
opening.
5. Unscrew the filter (4*) and take it out.
6. (model dependent)
To wash the filter, you may:
a. Place the filter under the water tap and wash it up
until calc residues are removed. Squeeze the filter
f
as indicated in the picture E.
b. Immerse the filter in tap water (250 ml) mixed with
a measure (25 ml) of descaling fluid.
The descaling fluid can be obtained from our After-
sales service or from our website.
Accessory code
(After-sales)
7. Holding your steam generator in the lateral position
and using a jug, fill the boiler with 1/4 litre of water
and replace the filter.
8. Shake the base unit for a few moments, unscrew the
filter again and empty the boiler completely over a
sink or bucket.
For best results, we recommend that this operation
f
is performed twice.
Important: before re-closing, make sure no water
remains in the boiler.
9. Replace and tighten up the filter.
To reset the "Calc'n'Clean" counter, switch the
steam station off twice, keeping it off for at least 30
seconds each time.
(on → 30s off → on → 30s off → on)
Rinsing the iron steam chamber (F)
Caution! Risk of burns!
This procedure helps to remove scale particles out of
the steam chamber.
Carry it out approximately every 2 weeks, if the water in
your area is very hard.
a) Ensure that the iron is cooled down.
b) Set the temperature selector (15) of the iron to the
"min" position.
c) Fill the tank with tap water.
Name of accessory
(Online shop)
311144 TDZ1101
d) Plug in the mains cable and set the main power
switch (12) to the "I" position (illuminated in red)
e) Wait until the "steam ready" indicator lamp (9) lights
up.
f) If the steam station has steam regulator (10*), set it
to the maximum position.
g) Hold the iron over the sink or a container to collect
the water.
h) Press the steam release button (16) and gently
shake the iron. Boiling water and steam will come
out, carrying scale and or deposits that might be
there. This could take approximately 5 minutes.
i) Set the temperature selector (15) of the iron to the
"max" position, without pressing the steam release
button (16). The water in the steam chamber will
start evaporating. Wait until all the water inside the
chamber has been evaporated.
j) To clean the soleplate, immediately rub off any
residue by running the hot iron over dry cotton cloth.
Cleaning & Maintenance
Attention! Risk of burns!
Always unplug the appliance from the mains supply
before carrying out any cleaning or maintenance
operation on it.
1. After ironing, pull out the plug and allow the appliance
to cool down before cleaning.
2. Wipe the housing, handle and iron body with a damp
cotton cloth.
3. If the soleplate is soiled with dirt or scale, clean it
with a damp cotton cloth.
4. If the cloth is synthetic, it may melt due to the high
temperature on the soleplate (19). Switch off the
steam and rub off any residue immediately with a
thickly folded, dry cotton cloth.
5. Never use abrasive products or solvents. To keep
the soleplate (19) smooth, you should avoid hard
contact with metal objects. Never use a scouring
pad, or chemicals to clean the soleplate.
Storing the appliance (G)
1. Always allow the appliance to cool down before
storing it.
2. Set the main power button to the "0" position (the red
light will go off) and disconnect the mains cable.
3. Place the iron on the iron pad (2), standing on the
soleplate, and fix it by inserting the tip of the iron into
the front slot and moving the lock lever (13) against
the heel of the iron.
4. Store the mains cable (6) and steam hose (7) in the
storage compartment (5). Do not wrap the cords too
tight.
5. Hold the iron´s handle when moving the appliance,
as shown in figure G, or use the carrying handles (3)
on the sides.
en
13