Technical Data; Dust/Chip Extraction - Bosch PSB 500 RE Manual Original

OBJ_DOKU-27099-001.fm Page 12 Monday, July 11, 2011 11:44 AM
12 | English

Technical Data

Impact Drill
Article number
Rated power input
Output power
No-load speed
Rated speed
Impact rate
Rated torque
Torque at max. output power
Right/left rotation
Spindle collar dia.
Max. drilling dia.
– Concrete
– Steel
– Wood
Chuck clamping range
Weight according to EPTA-Procedure 01/2003
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For different voltages and models for specific countries, these values can vary.
Please observe the article number on the type plate of your machine. The trade names of the individual machines may vary.
Assembly
Before any work on the machine itself, pull the mains
plug.
Auxiliary Handle (see figure A)
Operate your machine only with the auxiliary handle
10.
The auxiliary handle 10 can be set to any position for a secure
and low-fatigue working posture.
Turn the wing bolt for adjustment of the auxiliary handle 9 in
anticlockwise direction and set the auxiliary handle 10 to the
required position. Then tighten the wing bolt 9 again in clock-
wise direction.
Adjusting the Drilling Depth (see figure A)
The required drilling depth X can be set with the depth stop
11.
Press the button for the depth stop adjustment 8 and insert
the depth stop into the auxiliary handle 10.
The knurled surface of the depth stop 11 must face upward.
Pull out the depth stop until the distance between the tip of
the drill bit and the tip of the depth stop correspond with the
desired drilling depth X.
Changing the Tool (see figure B)
Keyless Chuck
Hold the rear sleeve 3 of the keyless chuck 1 tight and turn the
front sleeve 2 in rotation direction
serted. Insert the tool.
Hold the rear sleeve 3 of the keyless chuck 1 tight and firmly
turn the front sleeve 2 in rotation direction
2 609 005 557 | (11.7.11)
Screwdriver Tools
When working with screwdriver bits 14, a universal bit holder
13 should always be used. Use only screwdriver bits that fit
the screw head.
For driving screws, always position the "Drilling/Impact Drill-
ing" selector switch 4 to the "Drilling" symbol.
Replacing the Drill Chuck
For power tools without spindle lock, the drill chuck
must be replaced by an authorised after-sales service
agent for Bosch power tools.

Dust/Chip Extraction

Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-treat-
ment additives (chromate, wood preservative). Materials
containing asbestos may only be worked by specialists.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filter-class respirator.
Observe the relevant regulations in your country for the
materials to be worked.
, until the tool can be in-
Prevent dust accumulation at the workplace. Dusts can
easily ignite.
by hand.
PSB 500 RE
3 603 A26 0..
W 500
W 228
-1
min 50 – 3000
-1
min 2380
-1
min 48000
Nm 0.9
Nm 7.5
mm 43
mm 13
mm 10
mm 20
mm 2.0 – 13
kg 1.5
/II
The drill chuck must be tightened with a tightening
torque of approx. 6–8 Nm.
PSB 550 RE
3 603 A26 0..
550
270
50 – 3000
2246
48000
1.2
7.5
43
13
10
20
2.0 – 13
1.5
/II
Bosch Power Tools