Peg-Perego veloce Instrucciones De Uso página 21

_ Be careful not to hurt the child
when adjusting the mechanisms
(handlebar, backrest ... ).
_ Any weights hanging on the
handlebar or handles could make
the item unstable; follow the
manufacturer's instructions regards
the maximum loads transportable.
_ Any load applied to the handle and/
or the backrest and/or laterally to
the product can compromise the
stability of the product.
_ Do not load the baskets over
7 Kg. Do not put weight in the
cup holder (if present) in excess of
those indicated on the cup holders
themselves and never hot drinks. Do
not put loads of more than 0.2 Kg in
the hood pockets (if present).
_ Do not use the product near to
stairs or steps, heat sources, naked
flames or dangerous objects within
reach of the child.
_ Only replacement parts supplied or
recommended by the manufacturer/
distributor shall be used.
_ WARNING This product is not
suitable for running or skating.
_ WARNING Do not add any
mattress are not approved by the
manufacturer.
_ Do not use accessories which are
not approved by the manufacturer.
The images referring to the textile details may
differ from the collection purchased.
For more information, consult our website:
www.pegperego.com
INSTRUCTIONS
CHASSIS
1 OPENING: Before opening the frame, if present, remove
(without using blades) all the die-cut cardboard
elements.
- Press the two side buttons on the handle bar and rotate
it in line with the frame tube (fig.a).
- Move the safety button located behind the handle
bar (fig.b) to the right or left and fully press the central
button on the handle bar (fig.c).
- Open the chassis, release both buttons (b-c) and lift the
handle bar upwards (fig.d) until it is fully open and clicks
into place (fig_e).
2 FITTING THE WHEELS:
To assemble the front wheels, fit them into the slots until
they lock into place (fig_a).
To assemble the rear wheels, fit them into the slots until
they lock into place (fig_b).
3 FITTING THE REAR WHEEL MUD FLAP:
Insert and attach the mud flaps, as shown, on the
supports attached to the chassis' rear wheel mounts.
To remove or replace them: press in the opposite
direction and pull out.
4 OPENING THE SEAT: Open the seat from the ends, lifting
the backrest until it clicks into place.
5 FITTING THE BASKET:
First fasten the front part of the basket: slide the side ties
into the channels along the frame (fig.a) and then fasten
the three Velcro straps as shown (fig.b-c).
6 Fitting the rear part of the basket:
Slide the side ties into the channels along the frame
uprights (fig.a) and then fasten the Velcro strap as
shown, making sure you take in the tube (fig.b).
CAUTION! If you do not hook the basket on correctly, as
shown, the basket will be unable to support the weight
of loads placed in it.
7 FIXED OR SWIVELLING FRONT WHEELS: To lock the front
wheels, rotate the lever inwards (fig_a); to release the
wheels and make them swivel, rotate the lever outwards
(fig_b).
On difficult terrain, we recommend using fixed
wheels.
8 BRAKE: To brake the frame, press the rear of the pedal
and check that the indicator is red (fig a).
To unlock the frame, press the front of the pedal and
check that the indicator is green (fig b).
9 ADJUSTABLE HANDLE BAR: To adjust the height of the
handle bar, simultaneous press the side buttons, rotate
the handle bar to the required position, and release the
buttons (fig_a).
FITTING THE CUP HOLDER: It is possible to fasten the
cup holder to one of the mushroom buttons on the
frame, located both to the right and the left of the
handle bar (fig_b).
10 CLOSING THE CHASSIS WITH THE SEAT FASTENED:
It is possible to close the chassis with the child seat
mounted both forward-facing and rear-facing.
FORWARD-FACING:
Close the hood, pull the backrest adjustment handle
(fig_1) and fold this fully forward until it closes (fig_2).
11 Align the handle bar with the frame (fig_a), move the
safety button located behind the handle bar (fig.b) to
the right or left and fully press the central button on the
handle bar (fig.c).
Close the chassis, release both buttons (b-c) and push
the handle bar downwards (fig d), holding the chassis
vertical until it clicks into the closed position (fig.e).
12 REVERSING THE SEAT ON THE CHASSIS:
To release the seat, press the buttons on both sides as
shown (fig_a) and simultaneously lift the seat (fig_b).
Fasten the seat to the chassis, either in the forward-
facing (fig_c) or the rear-facing (fig_d) position.
To secure the seat to the frame/ support, place it
on the fastening devices until it clicks into place.
IMPORTANT: Ensure the seat is properly fastened.
13 REAR-FACING:
Close the hood, pull the backrest adjustment handle
(fig_1) and fold this fully forward until it closes (fig_2).
14 Align the handle bar with the frame (fig.a), move the
safety button located behind the handle bar (fig.b) to
the right or left and fully press the central button on the
handle bar (fig.c).
Close the chassis, release both buttons (b-c) and push
the handle bar downwards (fig d), holding the chassis
vertical until it clicks into the closed position (fig.e).
15 TRANSPORT: The stroller can be conveniently carried,
with the front wheels in fixed position, using the handle
bar aligned with the frame (fig_a).
To reduce the overall dimensions, you can lower the
handle bar (fig.b).
16 WHEEL REMOVAL
All the wheels can be removed to make the stroller even
more compact.
- 21 -