Using Your Cooktop; Surface Controls - JENN-AIR JGC9536 Guia Del Usuario

U
Y
SING OUR
S C
URFACE ONTROLS
CAUTION
• If flame should go out during a cooking
operation, turn the burner off. If a
strong gas odor is detected, open a
window and wait five minutes before
relighting the burner.
• Be sure all surface controls are set to
the OFF position prior to supplying
gas to the cooktop.
• NEVER touch cooktop until it has
cooled. Expect some parts of the
cooktop, especially around the
burners, to become warm or hot during
cooking. Use potholders to protect
hands.
S C
URFACE ONTROL
K
NOBS
Use to turn on the
surface burners. An
infinite choice of heat
settings is available from
Low to High. At the High
setting a detent or notch may be felt.
P I
ILOTLESS GNITION
Pilotless ignition eliminates the need for a
constant standing pilot light. Each surface
burner has a spark ignitor. Use care when
cleaning around the surface burner.
If the surface burner does not light, check
if ignitor is broken, soiled or wet.
C
OOKTOP
S
ETTING THE
C
ONTROLS
Your cooktop has sealed gas burners with
automatic re-ignition. If the burner flame
should go out, the system will automatically
spark to re-ignite the burner.
1. Place a pan on the burner grate. (To
preserve the grate finish, do not operate
the burners without a pan on the grate
to absorb the heat from the burner
flame.)
2. Push in knob and turn immediately
counterclockwise to the desired setting.
• A clicking (spark) sound will be
heard and the burner will light.
(All ignitors will spark when any
surface burner knob is turned on.
However, only the selected burner
will light.)
3. Visually check setting.
4. Do not leave unattended.
S
UGGESTED
G
UIDELINES
The size and type of cookware, type and
amount of food and BTU of the burner will
determine where to set the knob for
cooking operations. Use the graphics
printed around the knobs as a guide. The
following descriptions will aid in choosing
the setting that will give optimum results:
Hold or Warm: Food maintains a
temperature above 140° F without
continuing to cook. Food is heated on a
higher flame size until it reaches this
temperature and then the flame size is
reduced. Never use a hold or warm setting
to reheat cold food. Be sure knob is
adjusted to produce a stable flame. (Use
the LOW setting or the simmer burner to
keep food warm.)
Simmer: Food forms bubbles that barely
break the surface. Foods are between
185° F and 200° F. A simmer setting can
also be used to steam or poach foods or
continue cooking covered foods. (Adjust
the knob between High and Low to obtain
the desired simmer action.)
Slow Boil: Food forms bubbles at a
moderate pace. A slow boil setting can
also be used for most frying and for
maintaining the cooking of large amounts
of liquids. (Adjust the knob between High
and Low to obtain the desired boil action.)
Boil: Liquid forms bubbles at a rapid
pace. A fast boil setting can be used to
bring liquid to a boil, brown meat, stir fry,
saute, and heat oil for frying before turning
to a lower setting. The High setting is
always used to bring liquids to a boil.
Once the liquid boils, always reduce the
flame size to the lowest setting that will
maintain the boil action. (Turn the knob to
High then adjust the flame size to fit the
size of the pan.)
O
C
OOKING
P
1. Hold a lighted match to the desired
2. Push in and turn the control knob
• When lighting the surface burners,
• Do not leave the cooktop
D
PERATING URING A
F
OWER AILURE
surface burner head.
slowly to the desired setting.
CAUTION
be sure all of the controls are in the
OFF position. Strike the match first
and hold it in position before turning
the knob.
unattended when cooking during
a power failure. The automatic
re-ignition feature will not operate
during a power failure.