Cebora 125.00. Manual De Istrucciones página 16

CEBORA S.p.A.
10.10 AC / DC (TIG).
Green light indicates AC welding current.
Red light indicates DC welding current.
10.11 Pulsed TIG (TIG).
Green light indicates Pulsed TIG welding.
Red light indicates not Pulsed TIG welding.
10.12 Corner (PLASMA).
Green light indicates normal cutting condition.
Red light indicates corner approaching.
10.13 Spot (PLASMA).
Green light indicates normal cutting condition.
Red light indicates Spot mode activated.
11 ANALOG SIGNALS FROM ROBOT-
PANTOGRAPH CONTROL TO
POWER SOURCE.
GB
Analog Input signals information is updated
every 200 msec. in the Main Page, and every 100
msec. in the Log Page.
11.1 Speed Set Point (MIG).
Indicates the "Wire Speed Set Point" expressed
in m/min.
The allowed range is shown on the line.
The corresponding Robot Interface Analogue
Input voltage has the following ratio:
- 0.0 ÷ 25.0 m/min Wire Speed = 0 ÷ 10 V
Robot Interface input voltage.
11.2 Arc Length Correction (MIG).
Indicates the "Arc Length Correction" expressed
in Volts.
The allowed range is shown on the line.
The corresponding Robot Interface Analog Input
voltage has the following ratio:
- -9.9 ÷ +9.9 V Arc Length Correction = 0 ÷ 10
V Robot Interface input voltage.
- -9.9 V means minimum Arc Length.
- 0 V means neutral Arc Length (basic setting).
- +9.9 V means maximum Arc Length.
11.3 Inductance (MIG).
Indicates the "Inductance Correction" expressed
in absolute value.
The allowed range is shown on the line.
The corresponding Robot Interface Analogue
Input voltage has the following ratio:
- -9.9 ÷ +9.9 Inductance Correction = 0 ÷ 10 V
Robot Interface input voltage.
- -9.9 means hard and stable arc.
- 0 means neutral inductance (basic setting).
- +9.9 means soft arc with little or no spatter.
3.300.125-C
11.4 Burn-back Time Correction (MIG).
Indicates the "Burn-back Time Correction"
expressed in msec.
The allowed range is shown on the line.
The corresponding Robot Interface Analogue
Input voltage has the following ratio:
- -200 ÷ +200 msec.
Correction = 0 ÷ 10 V Robot Interface input
voltage.
- -200 minimum Burn-back time.
- 0 neutral Burn-back time (basic setting).
- +200 maximum Burn-back time.
11.5 Current Set Point (TIG).
Indicates the "Welding Current Set Point"
expressed in Amps.
The allowed range is shown on the line.
The corresponding Robot Interface Analogue
Input voltage has the following ratio:
- 0 ÷ 500 A output current = 0 ÷ 10 V Robot
Interface input voltage.
11.6 Wire High Speed Set Point (TIG).
Indicates the "Cold Wire High Speed Set Point"
expressed in m/min.
The allowed range is shown on the line.
The corresponding Robot Interface Analogue
Input voltage has the following ratio:
- -2.5 ÷ 10.0 m/min. Wire High Speed Set Point
= 0 ÷ 10 V Robot Interface input voltage.
11.7 Pulse Level Set Point (TIG).
Indicates the "Pulse Level Set Point" expressed
in percentage value.
The allowed range is shown on the line.
The corresponding Robot Interface Analogue
Input voltage has the following ratio:
- 0 ÷ 100% Pulse Level Set Point = 0 ÷ 10 V
Robot Interface input voltage.
11.8 Wire Low Speed Set Point (TIG).
Indicates the "Cold Wire Low Speed Set Point"
expressed in m/min.
The allowed range is shown on the line.
The corresponding Robot Interface Analogue
Input voltage has the following ratio:
- -2.5 ÷ 10.0 m/min Wire Low Speed Set Point
= 0 ÷ 10 V Robot Interface input voltage.
11.9 Corner Current Correction (PLASMA).
Indicates the "Corner Current Correction"
expressed in percentage value.
The allowed range is shown on the line.
- 50 % ÷ 100 % of the cutting current.
16
Burn-back Time
04/03/2016