Facom 1075.H Manual De Instrucciones página 3

EN
W/Cap
Length: W/Soldering Tip
W/Heat Blower Tip
Weight (when gas-filled)
Approximate temperature
soldering tip
Torch
Gas container capacity
Operating time
(one gas filling)
IMPORTANT SAFETY INSTRUCTIONS
Warnings:
• Unit contains flammable gas ( Butane) under pressure use with care.
• DO NOT expose to heat above +50°C (120°F) and avoid prolonged
exposure to the sun.
• DO NOT puncture or incinerate.
• Excessive gas flow, flaming or catalyst pulsing red may occur when the
regulator is incorrectly adjusted, i.e., set too high.
• DO NOT refill, ignite or use near open flame, heater, furnace or
combustible materials.
Keep unit away from face and body when igniting.
• KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries.
• KEEP AWAY FROM CHILDREN.
• STORE WHEN NOT IN USE. Store in dry, ocked cabinet out of reach of
children.
• Be extremely careful as torch flame tip temperature is over 1300°C
(2400°F)
• Be extremely careful as torch flame is almost invisible in dry light or strong
light.
• WEAR SAFETY GLASSES.
• DONT OVERREACH. Keep proper footing and balance at all times.
• STAY ALERT. Watch what you are doing.
Use common sense. Do not operate when you are tired.
• DO NOT TOUCH the heated tip or barrel of the unit.
• DO NOT leave unit unattended when it is operating or hot.
• ALWAYS BE SURE THE UNIT IS COOL BEFORE STORING.
• DO NOT REPLACE CAP WITHOUT SWITCHING UNIT OFF AND
ENSURING TIP HAS COOLED
• USE ONLY IN WELL VENTILATED AREA.
• DO NOT attempt to readjust or repair. Unit is not user serviceable.
Do ensure flame is extinguished before putting down.
• READ INSTRUCTION MANUAL PRIOR TO USE.
• BUTANE NOT INCLUDED.
HOW TO USE 1075.H
REFUELING
2.1 Make sure ON / OFF switch is at "OFF" position before filling.
2.2 Adaptors are not normally required when refilling.
2.3 To refill hold refill can as pictured (fuel transfer is dependent upon
gravity).
2.4 Stop filling when overflow gas.
IGNITION WARNINGS
3.A Do not touch tip, tip housing or knurled nut while igniting.
3.B Do not ignite the unit when "Tip Assembly" is not screwed on.
HOW TO USE SOLDERING IRON
3.1.1 Set gas control level at mid position.
3.1.2 Push the ON / OFF ignition switch slowly upward toward tip to the max. point
and release the switch. (see 3.1)
3.1.3 You may hear the sound of gas flowing and then the tip housing window will glow
orange after 1 or 2 seconds. If not, repeat 3.1.2
3.1.4 Tip temperature can be changed by adjusting the gas control lever.
3.1.5 To turn off, pull ignition switch down to the OFF position. lt is not necessary to
move the gas control lever after the unit is turned off.
SPECIFICATIONS
198 mm (7.80 in)
189 mm (7.44 in)
181 mm (7.13 in)
73 g
250°C ~ 550°C
(480°F ~ 1020°F)
1100°C (2012°F)
10 ml / 0.34oz.
55 min.
at mid setting
HOW TO USE BLOW TORCH
3.2.1 Remove tip and tip housing by untightening Knurled Nut.
3.2.2 Mount the same tip housing in place without tip.
3.2.3 lgnite gas by means of on/off ignition switch
(Same as above).
3.2.4 Adjust flame length. Do not adjust to maximum length
as gas may flare-up and turn off.
3.2.5 To shut off the unit, refer to (3.1.5)
HOW TO USE HEAT BLOW TIP
3.3 Same as soldering tip.
HOW TO USE HOT KNIFE TIP
3.4 Same as soldering tip.
ADJUSTMENT
4.1 The tip temperature can be adjusted by turning the GAS
CONTROL LEVER observing the - + signs on the body.
4.2 ldeally set the GAS CONTROL LEVER to mid position when
soldering.
4.3 lt is not necessary for the catalyst inside the tip to glow bright
red to achieve satisfactory soldering temperatures. Experience
will dictate the adjuster setting required.
Cap
CHANGING TIPS
5.1 Be sure the tip has cooled before removal.
5.2 The catalyst seen through the Hot Air Exhaust Hale of the
soldering tip is very delicate and will not sustain mechanical
abuse without serious damage.
5.3 The soldering tip is easily removable allowing the installation
Soldering
of other style tips or the replacement of a worn tip. After the
tip
soldering tip is cool, simply unscrew it with a counterclockwise
motion. Be careful not to overtighten as this could damage
the nozzle assembly and thread in the body.
Catalyst
REPLACE CAP
7.1 When replacing cap please refer as shown picture 7.1
CLEANING
8.1 Use only mild soap and a damp cloth to dean the housings of
the tool. Many household cleaners contain chemicals which
ON / OFF
adjuster couId seriously damage the plastic. Also do not use gasoline,
turpentine, lacquer or paint thinner, dry cleaning fluids or similar
products. Never let any liquid gel inside the tool; never immerse
any part of the tool into a liquid.
IMPORTANT NOTE:
THIS TOOL HAS BEEN ESPECIALLY DESIGNED FOR USE WITH GOOD QUALITY BUTANE
Gas tank
GAS. ANY OTHER FUEL GASES COULD CREATE MUCH HIGHER TEMPERATURES AND
INDUCE "FLARE UP" AT THE TIP EXHAUST SLOTS.
Filling
Valve
TROUBLESHOOTING
9. To reduce the risk of persona! injury, property damage, or damage to your 1075.H, do
not attempt to repair the unit body.
PROBLEM
Does not ignite.
Low gas pressure or
low flame.
Tip does not heat up.
SOLDER
DISPENSER
1075.HD
PROBABLE CAUSE HOW TO CORRECT
• Empty tank. • Refill with butane fuel.
• Too high or low fuel • Adjust control lever to a
pressure. higher or lower position.
• Push on/off ignition • Re-read «How to use as
switch loo fast. a soldering iron».
• Cold fuel. • Hold body in hands to allow
unit to warm up.
• Low fuel. • Refuel.
• Used-up catalyst. • Replace with new tip.
• lnsufficient fuel • Adjust control lever to a
pressure. higher position.
BASIC TIPS SOLDERING
1075.HS
1mm 2.4mm Hot Knife
Conical Chisel
Heat Blower