Fellowes AeraMax Pro AM II Manual De Instrucciones página 3

DISPLAY PANEL
1 2
NOTE: Manual mode will not be available for 1 minute upon initial power-up.
1 AIR QUALITY SENSOR – This indicator monitors the air quality and
adjusts the fan speed to keep your air purified. Blue indicates a low
level of contaminants detected, amber indicates a moderate level of
contaminants and red indicates a high level of contaminants.
2 AUTO MODE – To select, press and hold the button until icon
illuminates. This mode monitors air quality, motion, and noise level
to adjust the fan speed in order to keep your air purified as quickly
as possible. The fan has 5 speeds and can reach turbo speed to clean
the room in the case of high levels of contaminant. The number of tick
marks illuminated around this icon indicates fan speed. When Quiet
Mode is selected, the Auto Mode indicator will be purple. The machine
will continue to use EnviroSmart™ but only utilizes the 3 lowest, most
quiet of the 5 fan speeds. This button also includes QUIET MODE. To
select, press and hold until the button turns purple. The machine will
continue to use EnviroSmart ™ but only utilizes the 3 lowest, most
quiet of the 5 fan speeds.
3 MANUAL MODE – To select, press the button until icon illuminates.
This mode allows you to choose one of the 5 fan speeds and keep
the unit at this speed until AUTO MODE is chosen again. The internal
sensors will not adjust the fan speed in this mode. The number of tick
marks illuminated around the AUTO MODE icon indicates fan speed.
*Note - if hybrid filter is being used, both the HEPA and Carbon indicators will be lit.
OPERATION
The air purifier continuously works in automatic mode; The air purifier will operate through the 5 levels of speeds in order to clean room of contaminents.
Once air is cleaned, and no sensors are activated, the unit lowers to energy saving mode to reduce energy consumption and extend the life of the filters.
When Manual Mode is selected the Manual indicator on the control panel will be blue. This mode allows you to choose one of the 5 fan speeds and keep
unit at this speed until Auto Mode is chosen/selected.
4
AeraMaxPRO_AMII_230V_18L_411645_071219.indd 4-5
CARBON HEPA
3 4 5 6
4 PlasmaTRUE™ TECHNOLOGY – Creates an ionized field to help
safely remove airborne pollutants. To turn on and off the PlasmaTRUE™
TECHNOLOGY, touch and hold the PLASMA indicator. A blue light
illuminates when the PlasmaTRUE™ TECHNOLOGY is enabled. To disable
the PlasmaTRUE™ TECHNOLOGY, press and hold "Plasma" indicator
until light is off.
5 CARBON FILTER REPLACEMENT INDICATOR* – If the light is red
this indicates the filter needs replacing. The replacement period will
vary depending on the filters used, hours of use, air quality, and rate
of air flow. For filter replacement indicator descriptions see FILTER
REPLACEMENT section.
6 HEPA FILTER REPLACEMENT INDICATOR* – If the light is red
this indicates the filter needs replacing. The replacement period will
vary depending on the filters used, hours of use, air quality, and rate
of air flow. For filter replacement indicator descriptions see FILTER
REPLACEMENT INDICATORS section.
INSTALLATION
Please read instructions carefully before installing unit.
SAFETY
WARNING:
Be mindful of machine placement in relation to electric socket (cord length approx 5' 5").
To avoid the risk of electrocution confirm the electrical supply has been disconnected or switched off before beginning any installation work.
Confirm no electrical wiring, utility pipes, or duct work is located directly behind the installation / drilling area.
It is strongly recommended at least 2 mounting points for the air purifier be mounted to an existing stud. Requires 2 people for installation.
Follow Mounting Main Assembly Section instructions.
TOOLS RECOMMENDED FOR INSTALLATION
• Electric drill, drill bits (not included)
• # 2 Phillips and # 2 Flat Head screw drivers (not included)
• Wire nuts (not included)
• Level (not included)
• Stud finder
PARTS PROVIDED FOR INSTALLATION
• Drywall Anchors - 10mm OD
• Pan Head Phillips Screws
PRODUCT INSTALLATION GUIDELINES
If air purifier is being mounted high on the wall make sure the top edge of the unit is positioned at least 8" inches (21 cm) below the ceiling to allow
for filter replacement.
5
7/12/19 3:14 PM