1. Manuales
  2. Marcas
  3. Thermon Manuales
  4. Cables y Conectores
  5. Terminator ZP-L-XP
  6. Instrucciones de instalación

Thermon Terminator ZP-L-XP Instrucciones De Instalación

Kits conexion de alimentacion
Ocultar thumbs
1
2
3
4
5
6
7
8

Enlaces rápidos

Power Connection Kit
Installation Instructions
Terminator ZP-L-XP
for use with RSX, TSX, VSX self-regulating heating cables
Terminator ZP-S-XP
for use with BSX, HTSX, KSX self-regulating, HPT power-limiting,
and FP constant watt heating cables
Tel: +44 (0)191 490 1547
Fax: +44 (0)191 477 5371
Email:
Website:
www.heattracing.co.uk
www.thorneanderrick.co.uk
For Power Connection (1-3 Heating Cables), In-Line Splice Connection,
T-Splice Connection, or End Termination (1-2 Heating Cables) Applications
loading

Manuales relacionados para Thermon Terminator ZP-L-XP

Resumen de contenidos para Thermon Terminator ZP-L-XP

  • Página 1 Power Connection Kit Installation Instructions Terminator ZP-L-XP for use with RSX, TSX, VSX self-regulating heating cables Terminator ZP-S-XP for use with BSX, HTSX, KSX self-regulating, HPT power-limiting, and FP constant watt heating cables Tel: +44 (0)191 490 1547 Fax: +44 (0)191 477 5371 Email: [email protected]...

  • Página 2: Tools Required

    De-energize all power sources before opening enclosure. Installation must comply with Thermon requirements (including Keep ends of heating cable and kit components dry before and form PN 50207U for Ex systems) and be installed in accordance during installation.

  • Página 3: Installation Instructions

    Installation Instructions Locate bus connection (HPT and FP only) and cable as shown. Mount expediter to pipe using pipe band. Do not band over Cut end of cable at angle to aid in piercing grommet. Leave cable. additional cable for expansion loop. See page 4 for multiple cable installation tips.
  • Página 4 Installation Instructions Mount junction box base on expediter. Make sure to align Complete system wiring. Terminal set screws shall be slots to properly orient junction box base. Tighten nut with tightened to a torque value of 1.4 Nm (12.4 lb-in). See page Terminator-LN-Tool.

  • Página 5: Wiring Details

    Two Cable Layout Tips Mount expediter with three cables. Locate bus connection (HPT and FP only) and cable as Do not band over cable. shown. Cut end of cable at angle to aid in piercing grom- met. Leave additional cable for expansion loop. Wiring Details Insert two cables into expediter.
  • Página 6 Instructions d’installation des kits de connexion gaansluiting of eindafsluiting van de verwarmingskabel. ZP-S-XP pour utilisation avec les câbles chauffants Thermon de type BSX, HTSX, KSX, HPT et FP Duw eventuele overlengte van de verwarmingskabel terug. Draai de moer vast aan. Monteer de lus ZP-L-XP;...
  • Página 7 показано конечное соединение кабелей. • La instalación debe cumplir los requisitos de Thermon e instalarse de acuerdo con la normativa Вставьте кабель в монтажную колонку. Если монтаж производится на нижней части трубы, vigente como la norma EN IEC 60079-14 para zonas clasificadas con riesgo de explosión (en su сделайте...
  • Página 8 Facsimile: +31-(0)15-36 15 379 Website: www.thermon.com Corporate Headquarters Thermon Manufacturing Company 100 Thermon Drive • San Marcos, TX 78666 • U.S.A. Phone: +1-512-396-5801 • Facsimile: +1-512-396-3627 For the Thermon office nearest you visit us at www.thermon.com THERMON...The Heat Tracing Specialists ...

Este manual también es adecuado para:

Terminator zp-s-xp