Important Safeguards - Andis MBG-5 Manual Del Usuario

E N G L I S H
Please read the following instructions before using your new Andis
clipper. Give it the care that a fine, precision built instrument
deserves and it will give you years of service.

IMPORTANT SAFEGUARDS

When using an electrical appliance, basic precautions should
always be followed, including the following: Read all
instructions before using the Andis clipper.
DANGER:
To reduce the risk of electric shock:
1. Do not reach for an appliance that has fallen into water.
Unplug immediately.
2. Do not use while bathing or in a shower.
3. Do not place or store appliance where it can fall or be pulled
into a tub or sink. Do not place in or drop into water or other
liquid.
4. Except when charging, always unplug this appliance after use.
5. Unplug this appliance before cleaning, removing or
assembling parts.
WARNING:
To reduce the risk of burns, fire, electric
shock, or injury to persons:
1. An appliance should never be left unattended when plugged in.
2. This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
3. Children should be supervised to ensure that they do not play
with the appliance.
4. Use this appliance only for its intended use as described in this
manual. Do not use attachments not recommended by Andis.
5. Never operate this appliance if it has a damaged cord or
plug, if it is not working properly, if it has been dropped or
damaged, or dropped into water. Return the appliance to an
Andis authorized service station for examination and repair.
2
6. Keep the cord away from heated surfaces.
7. Never drop or insert any object into any opening.
8. Do not use outdoors or operate where aerosol (spray) products
are being used or where oxygen is being administered.
9. Do not use this appliance with a damaged or broken blade or
comb, as injury to the skin may occur.
10. To disconnect turn control to OFF then remove plug from outlet.
11. WARNING: During use, do not place or leave appliance
where it may be (1) damaged by an animal or (2) exposed
to the weather.
12. This appliance is intended for trimming purposes only.
SAVE THESE INSTRUCTIONS
THIS PRODUCT INTENDED FOR HOUSEHOLD USE
OPERATING INSTRUCTIONS
To reduce the risk of electric shock, this appliance has a polarized plug (one blade is
wider than the other). This plug will fit in a polarized outlet only one way. If the plug
does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet. Do not change the plug in any way.
Before starting clipper, remove blade guard (some models may not have a blade
guard). Plug cord into electrical outlet, operate at 120 volt, 60 cycle AC electrical
current or as noted on the unit. After using your clipper, rewrap cord and store in a
safe place.
2-SPEED OPERATION
To start clipper, move switch to either normal or high speed setting (Figure A).
Use the normal setting (switch in lowest position) for most cutting needs. Use the high
speed setting (switch in highest position) for cutting through heavy hair. To stop
clipper, move switch back to original (center) position.
USING THE ATTACHMENT COMBS
(Some models do not have combs and sizes will vary by kit)
You can set the blades for a longer cut by using any of the attachment combs made
for your Andis clipper. The combs mount easily; simply slip the cutter blade teeth into
comb and snap the comb down (Figures B & C). To remove, simply snap off. These
attachment combs guide hair into the blades and give you precise control of hair
lengths. The length of trim is indicated on the attachment comb. Use the chart to find
the approximate lengths of cut. Different blade angles in relation to the skin, thickness
and texture of the hair will vary the cutting length.
3