Milwaukee 6497 Manual Del Operador página 9

Adjusting the Miter Angle
The miter mechanism on the MILWAUKEE Magnum
Miter Saw has detent settings for commonly cut angles (0°, 15°, 22.5°
30°, and 45°). These detents make for quick, accurate set up of common
angles. In addition to the spring-loaded detents there is also a detent
override. The detent override, when engaged, allows the turntable to
smoothly rotate to any miter angle. The turntable can be easily locked at
any miter angle. The detent override is especially useful when making
small adjustments near 0°, 15°, 22.5° 30°, and 45°.
The saw cuts miter angles from 51° on the left to 59° on the right. Angle
markings appear on the scale that runs along the perimeter of the base.
1. To select a positive angle stop, loosen the clamp handle.
Pull the detente override lever and rotate the turntable to the desired
angle.
Tighten the clamp handle.
2. To select other angles, use the override mechanism, which allows
quick and accurate adjustments at any angle.
Pull up on the detent override lever and lock it by pushing in the
detent override lock.
Rotate the turntable to the desired angle.
Tighten the clamp handle securely clockwise.
Adjusting the Bevel Angle
The bevel mechanism has two positive sping-loaded stops: one at 0°
and one at 45°. The mechanism can be adjusted to any angle in between
by using the bevel angle scale. The bevel mechanism also has several
degrees of overtravel on both the left and right; the saw can be adjusted
to 48° on the left and to negative 3° on the right. To obtain the overtravel,
apply several pounds of force on the saw handle to override the spring-
loaded stops. Do not attempt to exceed the stated overtravel.
1. To adjust the bevel angle, place one hand on the front handle for
better control. Using the other hand, loosen the bevel adjustment
lever counterclockwise
2. Pull or push the saw handle to desired position, using the bevel
angle scale as a guide.
3. Tighten the bevel adjustment lever clockwise securely.
Adjusting the Depth of Cut (Fig. 4)
A hex cap screw with a lock nut controls the depth of cut. This cut can
be adjusted when cutting grooves, rabbets, or other operations
Fig. 4
head cap
1. Unplug the tool.
2. Loosen the lock nut by turning counterclockwise.
3. To set the saw for maximum depth of cut, unscrew the hex cap
screw so that it doesn't extend from the bottom of the saw arm.
To limit the depth of cut, screw the hex cap screw through the saw
arm. The more the screw is driven through the shallower the cut is.
4. Securely tighten the lock nut.
5. Make a sample cut and adjust as necessary.
®
Slide Compound
Socket
screw
Using the Flip Fence (Fig. 5, 6, & 7)
The quick-change flip fence can be positioned for simple miter cuts
(Fig. 5) and for bevel and compound cuts (Fig. 6). This helps to provide
superior support for both types of cuts.
Fig. 5
Fig. 6
1. To adjust the fence, loosen the fence lock lever (counterclockwise)
(Fig. 7). When the fence lock lever is parallel with the fence slot, pull
the fence away from the saw. A firm detent must be overridden to
accomplish this.
Fig. 7
2. Position the fence for the desired cut. Always position the fence
properly for maximum work support.
3. With the fence lock lever parallel to the fence, insert the fence lock
lever through the fence slot. Turn the fence lock lever clockwise to
secure the fence to the tool.
NOTE: The clamp on the mechanism must be rotated to a vertical
position, 90° to the slot. This position is required for proper clamping.
Starting and Stopping the Tool
Always hold the handle firmly because the starting and stopping action
locknut
of the motor may cause the handle to move up or down slightly. Always
secure the turntable by tightening the clamp handle when setting miter
angles. Always make sure the spindle lock is released so the blade is
free to rotate.
1. To start the motor, pull the trigger.
2. To stop the motor, release the trigger.
For miter cuts
For bevel and
compound cuts
Fence lock lever
Fence slot
page 9