DeWalt DXAEWPC4 Manual De Instrucciones página 6

Setting Up the Unit
Mounting the Battery Charger
This battery charger is designed so that it can be mounted on a flat
surface. The unit has four mounting holes at the corners of the unit.
CAUTION – To reduce the risk of product damage:
• Ensure that all installation and operating instructions and safety
precautions are understood and carefully followed by anyone
mounting or using the battery charger. Follow the steps outlined in
the "Important Safety Instructions" section of this manual.
• Always disconnect the charger at AC power source and at battery
terminal before mounting the unit.
• When the battery charger is mounted, do not hang anything additional
on the battery charger or risk of breakage may occur.
1. Position the unit as desired on a flat wall surface near a functioning
AC outlet. Make sure the surface is flat and free of obstruction so
the unit rests flush with the surface. Mark a dot on the wall through
each of the four mounting holes on the front of the unit.
DXAEWPC4_ManualENSP_062117.indd 10-11
2. Using an 0.2-inch (5mm) diameter bit, drill one hole for each of the
dots marked on the wall to a depth of approximately 1.18-1.37
inches (35-40mm).
3. Install a wall anchor (not Included) in each of the holes. Check that
the wall anchors are fully and securely inserted into the wall.
4. Make sure the unit is mounted in the correct direction. Align and
screw one PA3x60 screw (not Included) into each of the wall
anchors through the four screw holes on the front of the unit. Do
not over-tighten as this will damage the housing.
Using the Hanging Hook
The hanging hook allows you to position the battery charger for
convenient, hands-free operation; and can also be detached from the
unit for easy storage.
To detach the hanging hook, press and hold the hook release button
and lift the hook out of the hook slot.
To reattach, gently snap the hook back into the hook slot.
CAUTION – To reduce the risk of product damage:
• When the battery charger is hung by the hanging hook, do not shake
the charger or object that it is hanging from.
• Do not hang the charger from any electrical wires or anything that
it is not secure.
• Only use the hanging hook for hanging the charger. The hanging hook
is not intended to support additional weight. Do not hang anything
additional to the hanging hook or risk of breakage may occur.
Operating Instructions
Charging Using the Supplied Battery Clips
WARNING – To reduce the risk of injury or property damage:
• Always disconnect the AC plug from the AC outlet first before
disconnecting the charger from the battery to be charged.
10
• Ensure that all installation, operating instructions and safety
precautions are understood and observed; then follow the steps
outlined in the appropriate section ("Charging a battery installed
in a vehicle" or "Charging a battery that has been removed from a
vehicle").
1. Insert the double barrel tip of the battery clamp cable into the
double barrel tip of the battery charger cable (male-to-female and
female-to-male). Then plug the battery charger's power cord into
an AC outlet. The power LED will light blue to indicate that the
charger is plugged in and ready.
NOTE: If the Power LED does not come on, check connection
with the AC outlet. Make sure the AC outlet is functional.
2. Connect the battery charger to the battery using the battery clamps,
following the appropriate directions in the "Preparing to Charge"
section at the front of this manual.
3. When the unit is properly connected and charging, the battery
charging LED ( ) will light yellow to indicate the battery is charging.
NOTES:
A. If the Charging LED did not come on, check the connection to
the battery. If the clamps are properly connected, the battery
may be in fault condition. Manufacturer suggests to have the
battery tested by a qualified battery service technician.
B. If the clamps are incorrectly connected with regard to polarity,
the reverse polarity/fault LED ( ) will light. Unplug the
charger; then remove the clamps. Reconnect the clamps
properly.
4. When the charging complete LED ( ) lights green, the battery is
fully charged.
When disconnecting charger, disconnect AC cord, remove clamp from
vehicle chassis, and then remove clamp from battery terminal.
Charging Using the 12 Volt DC Accessory
Plug
CAUTION – To reduce the risk of property damage: Make sure that
the vehicle's accessory outlet is clean and free of debris before
connecting the unit.
1. Insert the double barrel tip of the 12 volt DC accessory plug cable
into the double barrel tip of the battery charger cable (male-to-
female and female-to-male). Then plug the battery charger's power
cord into an AC outlet. The power LED will light blue to indicate
that the charger is plugged in and ready.
NOTE: If the Power LED does not come on, check connection
with the AC outlet. Make sure the AC outlet is functional.
2. Insert the grooved tip of the 12 volt DC accessory plug into the
vehicle's 12 volt DC accessory outlet. Rotate the adapter slightly
to make sure there is good contact.
3. When the unit is properly connected and charging, the battery
charging LED ( ) will light yellow to indicate the battery is charging.
NOTES:
A. If the Charging LED did not come on, check the connection to
the vehicle's DC accessory outlet. Rotate the adapter slightly
to make sure there is good contact. If it is properly connected,
the battery may be in fault condition. Manufacturer suggests
to have the battery tested by a qualified battery service
technician.
B. Some vehicles require that the ignition be turned to the ACC
(accessory) position to activate the DC accessory outlet.
If your vehicle ignition is required to be turned to the ACC
position, be sure all the vehicle accessories (i.e. heater, fan,
radio, TV, lights... etc) are turned off. If not turned off, the
charger might not be able to charge the battery.
4. When the charging complete LED ( ) lights, the battery is fully
charged.
11
6/21/2017 10:14:03 AM