Tabla de contenido
Idiomas disponibles
Idiomas disponibles
2.3
OPERATION
•
Keep hands and feet away from rotating parts. Always
avoid the discharge chute opening.
•
The snow thrower must never be used to remove anything
but snow
•
Be careful when driving on or crossing gravel paths,
pavements and roads. Be aware of hidden dangers and
traffic.
•
Never direct the discharge chute towards a public road or
traffic.
•
If the snow thrower hits a foreign object, stop the engine,
disconnect the spark plug cable and carefully inspect the
machine for damage. Repair the damage before using the
machine again.
•
If the machine starts vibrating abnormally, stop the
engine and look for the cause. Vibration is normally a
sign of something wrong.
•
Stop the engine and disconnect the spark plug cable:
a. If the machine steers away from the driving position.
b. If the auger housing or discharge chute is blocked and
must be cleaned.
c. Before beginning repairs or adjustments.
•
Always make sure the rotating parts have stopped and all
the controls are disengaged before cleaning, repairing or
inspection.
•
Before leaving the machine unattended, disengage all the
controls, put it into neutral gear, stop the engine and set
the stop switch in position "OFF".
•
Never run the engine indoors except when taking it in and
out of its place of storage. In this case ensure the door to
the storage place is open. Exhaust fumes are toxic.
•
Never drive across a slope. Move from the top down, and
from the bottom to the top. Be careful when changing
direction on a slope. Avoid steep slopes.
•
Never operate the machine with insufficient protection or
without the safety devices in place.
•
Existing safety devices must not be disconnected or
disengaged.
•
Do not alter the engine's regulator setting and do not race
the engine. The possibility of personal injury increases
when the engine is run at high revs.
•
Never use the snow thrower near enclosures, cars,
windowpanes, slopes etc. without properly setting the
discharge chute deflector.
•
Always keep children away from areas to be cleared. Get
another adult to keep the children under supervision.
•
Do not overload the machine by driving it too fast.
•
Take care when reversing. Look behind you before and
during reversing to check for any obstacles.
•
Never point the discharge chute towards bystanders. Do
not allow anyone to stand in front of the machine.
•
Disengage the auger when the snow thrower is to be
transported or is not in use Do not drive too fast on
slippery surfaces when transporting.
•
Only use accessories that are approved by the machine's
manufacturer.
•
Never drive the snow thrower in bad visibility or without
satisfactory lighting.
•
Always ensure you have a good balance and a tight grip
on the handle.
•
Do not touch engine components because they are warm
during use. Risk of burn injuries.
ENGLISH
2.4
•
Tighten all nuts and screws so that the machine is in safe
working condition. Check the shear bolts regularly.
•
Always use genuine spare parts. Non-genuine spare parts
can entail a risk of injury, even if they fit the machine.
•
Never store the machine with petrol in the tank in
buildings where the fumes can come into contact with
open flames or sparks.
•
Allow the engine to cool before putting the machine in
store.
•
Before a long storage, check the instructions for
recommendations.
•
Replace damaged warning and instruction stickers.
•
Let the engine run a couple of minutes with the auger
connected after use. This prevents the auger from
freezing solid.
3.1
1. Remove all loose items from the carton.
2. Cut the four corners of the carton and let the sides fall
down.
3. Roll the snow thrower from the carton.
3.2
The carton contains details as per the table below. Some of
the details are shown in fig. 1:
Detail
Snow thrower
Discharge chute with details
Handle with levers
Wire attachments
Instructions of use
Funnel
Chute clearing tool
Bag with the following details:
Stop switch for spare
Break bolts for spare
Screws and nuts for the chute
3.3
1. Dismount the four locking knobs (2:T) with dished
washers from the handle lower part.
2. Fix the handle on the bolts.
3. Assemble the four dished washers and tighten with the
four locking knobs.
4. Fix the vires with the three attachments (2:X).
3.4
1. Place the chute on the flange. See fig. 3.
2. Assemble the four screws from the top and tighten with
the four nuts from the bottom.
Translation of the original instructions
MAINTENANCE AND STORAGE
3 ASSEMBLY
UNPACKING
CONTENTS
ASSEMBLY OF HANDLE
ASSEMBLY OF CHUTE
EN
Pos Num-
ber
1
A, B
1
1
X
3
-
1
-
1
G
1
1
2
4
41
Tabla de contenido
