Tabla de contenido
Idiomas disponibles
Idiomas disponibles
MAINTENANCE
WARNING!
To reduce the risk of injury,
always unplug your tool before
performing any maintenance.
Never disassemble the tool or try
to do any rewiring on the tool's
electrical system. Contact a
MILWAUKEE service facility for
ALL repairs.
Maintaining Tools
Keep your tool in good repair by adopting a
regular maintenance program. Before use,
examine the general condition of your tool.
Inspect guards, switches, tool cord set and
extension cord for damage. Check for
loose screws, misalignment, binding of
moving parts, improper mounting, broken
parts and any other condition that may af-
fect its safe operation. If abnormal noise
or vibration occurs, turn the tool off imme-
diately and have the problem corrected
before further use. Do not use a damaged
tool. Tag damaged tools "DO NOT USE" until
repaired (see "Repairs").
Under normal conditions, relubrication is
not necessary until the motor brushes
need to be replaced. After six months to
one year, depending on use, return your
tool to the nearest MILWAUKEE service
facility for the following:
•
Lubrication
•
Brush inspection and replacement
•
Mechanical inspection and cleaning
(gears, spindles, bearings, housing,
etc.)
•
Electrical inspection (switch, cord,
armature, etc.)
•
Testing to assure proper mechanical
and electrical operation
Cleaning
Clean dust and debris from vents. Keep
the tool handles clean, dry and free of oil
or grease. Use only mild soap and a damp
cloth to clean your tool since certain clean-
ing agents and solvents are harmful to plas-
tics and other insulated parts. Some of
these include: gasoline, turpentine, lacquer
thinner, paint thinner, chlorinated cleaning
solvents, ammonia and household deter-
gents containing ammonia. Never use flam-
mable or combustible solvents around
tools.
WARNING!
To reduce the risk of injury,
electric shock and damage to the
tool, never immerse your tool in
liquid or allow a liquid to flow
inside the tool.
Repairs
If your tool is damaged, return the entire
tool to the nearest service center listed on
the back cover of this operator's manual.
Brush Life
Proper care and lubrication are important
factors in prolonging the useful life of this
tool. This tool has been lubricated at the
factory.
Under
normal
conditions,
relubrication is not necessary until brush
replacement is called for. The need for
brush replacement is indicated by one or
more of the following:
•
Excessive arcing between brushes
and commutator
•
Inefficient or interrupted operation
•
Failure of the tool to start
10
ACCESSORIES
To reduce the risk of injury,
always unplug the tool before
attaching or removing accesso-
ries.
Use
recommended accessories. Oth-
ers may be hazardous.
For a complete listing of accessories refer to your MILWAUKEE Electric Tool catalog or go
on-line to www.mil-electric-tool.com. To obtain a catalog, contact your local distributor or
a service center listed on the back cover of this operator's manual.
14 Gauge Shear Blade Set (for Cat. No. 6815)
Cat. No. 48-44-0112
16 Gauge Shear Blade Set (for Cat. No. 6805)
Cat. No. 48-44-0122
TWO YEAR TOOL
LIMITED WARRANTY
Every MILWAUKEE tool is tested before leaving the factory and is warranted to be free
from defects in material and workmanship. MILWAUKEE will repair or replace (at
MILWAUKEE 's discretion), without charge, any tool (including battery chargers) which
examination proves to be defective in material or workmanship from two (2) years after
the date of purchase. Return the tool and a copy of the purchase receipt or other proof of
purchase to a MILWAUKEE Factory Service/Sales Support Branch location or MILWAUKEE
Authorized Service Station, freight prepaid and insured. This warranty does not cover
damage from repairs made or attempted by other than MILWAUKEE authorized personnel,
abuse, normal wear and tear, lack of maintenance, or accidents.
Battery Packs, Flashlights, and Radios are warranted for one (1) year from the date of
purchase.
THE REPAIR AND REPLACEMENT REMEDIES DESCRIBED HEREIN ARE EXCLUSIVE. IN NO
EVENT SHALL MILWAUKEE BE LIABLE FOR ANY INCIDENTAL, SPECIAL, OR CONSE-
QUENTIAL DAMAGES, INCLUDING LOSS OF PROFITS.
THIS WARRANTY IS EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, OR CONDI-
TIONS, WRITTEN OR ORAL, EXPRESSED OR IMPLIED FOR MERCHANTABLILITY OR FITNESS
FOR PARTICULAR USE OR PURPOSE.
This warranty gives you specific legal rights. You may also have other rights that vary
from state to state and province to province. In those states that do not allow the exclusion
of implied warranties or limitation of incidental or consequential damages, the above
limitations or exclusions may not apply to you. This warranty applies to the United States,
Canada, and Mexico only.
WARNING!
only
specifically
Feeler Gauge
Cat. No. 49-11-0080
9/64" Allen Wrench
Cat. No. 49-96-0065
5/64" Allen Wrench
Cat No. 49-96-0040
Type "G" Grease, 1lb. Can
Cat. No. 49-08-4140
11
Tabla de contenido
