Tabla de contenido
Idiomas disponibles
Idiomas disponibles
OPERATION
NOTE: When pad becomes soiled, remove pad and
turn over to expose clean side. Remove and wash pad
after both sides become soiled.
7. To stop machine, rotate the twist grips backwards
and hold handles firmly until machine comes to a
complete stop. The safety lock button will
automatically engage.
FOR SAFETY: When using machine, do not
release handles until pad comes to a complete
stop.
NOTE: The machine's circuit breaker may trip under
conditions of excessive overload. Change to a less
aggressive pad/brush and periodically check pad for
soil build- -up. To reset circuit breaker switch, wait 15
seconds and press the reset button located on the
handle.
8. Do not operate the machine in the same spot for a
long period of time. Floor damage may result.
9. To maneuver over thresholds and floor grates,
stop the machine and tilt it back on the transport
wheels.
10. When machine is not in use, do not leave machine
standing on the pad/brush. Pad/brush damage
may result.
11. When done scrubbing perform the following
machine maintenance procedures.
OPERATING THE OPTIONAL SOLUTION TANK
1. Fill the solution tank with a recommended solution.
WARNING: Fire or Explosion Hazard.
Never Use Flammable Liquids.
FOR SAFETY: When using machine, follow mixing
and handling instructions on chemical containers.
2. Lower handle to working position. Pull the solution
control knob to disperse solution to the pad/brush.
CLEANING CARPETS
Shampoo carpet brush required. Do not use a brush
that is intended for hard floors; personal injury and
carpet damage may result. Order Shampoo Carpet
Brush p/n 604989--17", 607463--20" or consult your
distributor or dealer for recommendations.
Before operating the machine on carpet, the carpet
must be presprayed with an approved cleaning
solution. The solution will act as a lubricant to allow
the shampoo brush to spin with little resistance.
FOR SAFETY: To avoid a jolt when starting the
machine on carpet, use a recommended shampoo
carpet brush and prespray the carpet.
8
Home Find... Go To..
When using the Dual Speed model to clean
carpets, do not operate machine at high speed;
personal injury may result.
For best cleaning results allow the presprayed
cleaning solution to "dwell" on the carpet for
approximately 10--12 minutes before scrubbing. Using
only a shampoo carpet brush, operate the machine at
a gradual, steady pace.
After scrubbing, while carpet is still wet, use an
extractor or wet--vacuum to pick up suspended soil
and foam. Then vacuum carpet when it's completely
dry.
MACHINE MAINTENANCE
WARNING: Electrical hazard. Unplug Power
Cord Before Servicing Machine
1. Remove and clean the pad driver/brush after each
use.
2. Clean the machine base after each use.
3. If equipped, rinse solution tank and solution supply
hose with clear water.
4. Inspect power cord for damage after each use. If
worn or damaged, replace immediately.
5. Wipe the power cord with damp cloth and neatly
coil it around cord hook and handle after each use.
6. Periodically check that all bolts and nuts are tight.
7. Every 250 hours of operation, check the motor for
carbon brush wear. Replace brushes when worn
to a length of 1 cm (0.38 in) or less. Contact an
Authorized Service Center for carbon brush
inspection.
FOR SAFETY: When servicing machine, all repairs
must be performed by a qualified service person.
TRANSPORTING MACHINE
1. Unplug the power cord and remove the pad from
the machine. Neatly coil the cord around the cord
hook and handle to prevent cord damage.
2. Load the machine using a recommended loading
ramp or carefully lift the machine with adequate
assistance.
FOR SAFETY: When transporting machine, get
assistance when lifting machine.
3. Secure machine with tie--down straps when
transporting by vehicle.
Tennant 2000/2010/2030/2040/2160/2170 (09- -06)
Capítulos
Tabla de contenido
