Eaton All-Pro Revolve REV32735M Manual De Instrucciones

MOTION ACTIVATED
REV32735M/ REV32735MW
REV32750M/ REV32750MW
FLOOD
REV335F/REV335FW
REV350F/REV350FW
DUSK TO DAWN
REV335PC/REV335PCW
REV350PC/REV350PCW
(Bronze/Bronce) and (White/Blanco)
ENGLISH
ITEMS REQUIRED
(Purchase separately)
• Phillips screwdriver
• Outdoor weatherproof silicone caulking
IMPORTANT SAFETY INSTRUCTIONS
When using product, basic precautions should always be followed, including the following:
• Heed all warnings, including below warnings AND those included on product.
• Save these instructions and warnings.
• For outdoor use only.
• cULus LISTED for wet location.
• Disassembling your fixture will void the warranty.
• Your fixture is prewired and preassemble for easy installation.
WARNING
• Read and follow these instructions.
• Risk of fire/electric shock. If not qualified, consult an electrician.
• Disconnect power at fuse or circuit breaker before installing or servicing.
CAUTION
• Not for use with a dimmer switch.
• Connect fixture to a 120 volt, 60 Hz power source. Any other connection voids
the warranty.
• Fixture should be installed by persons with experience in household wiring or by a
qualified electrician. The electrical system, and the method of electrically connecting
the fixture to it, must be in accordance with the National Electrical Code and local
building codes.
• Motion activated fixture designed for eave mount to a junction box only. Mount fixture
to a grounded, recessed-mounted standard junction box marked for use in wet
locations.
• Do not mount below 5 feet.
• This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
WARNING: FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by the manufacturer
could void the user's authorization to operate this equipment.
Questions?/ ¿Preguntas? 1-800-334-6871 [email protected]
PACKAGING CONTENTS/CONTENIDO DEL PAQUETE
A. Light fixture B. Adjustable Mounting
Bracket
Accesorio
Soporte de montaje
ajustable
E. (2) #10-24 x 1-1/4 in. cover
mounting screws (pre-attached)
(2) Tornillos #10-24 x 1-1/4 pulg.
de montaje de la cubierta (préfixé)
C. (2) #8-32 x 3/4 in. and (2) #10-24 x 3/4 in. junction
box screws (use the size that fits your junction box)
(2) Tornillos #8-32 x 3/4 pulg. y (2) tornillos #10-24 x 3/4
pulg. para montaje de la caja de conexiónes (utilice el
tamaño que mejor se adecue a su caja de conexiónes)
F. (2) Decorative screw cover caps
(2) Cubiertas tapatornillos
decorativas
SAVE THESE INSTRUCTIONS.
FOR BEST RESULTS
• Rotate the optics into position prior to installing the fixture. Use the optic
rotator tool (H) if necessary by firmly pressing against fixture housing and rotating
slowly.
• Install light 10-15 feet above the ground.
• Do not mount fixture close to reflective surfaces such as windows, white walls, white
surfaces, and water.
• When installing two fixtures on one switch, make sure the switch is rated for at least a
1 A inductive load.
MOUNTING AND WIRING YOUR FIXTURE
WARNING: Risk of electric shock. Disconnect
power at fuse or circuit breaker before installing
or servicing.
NOTE: Mounting bracket (B) mounts to recessed
standard fixture junction boxes. Junction box must have
at least 1-1/2 in. depth for proper installation.
CAUTION: Fixture MUST be installed utilizing a junction
box that is firmly and permanently attached to the
supporting joist or beam nearest the installation. Soffit
material alone will not safely support the fixture.
1. The mounting bracket is designed to provide
adjustment of the fixture's position for a finished
look. The mounting bracket can be used with or
without the locking screws (I). To lock the mounting
bracket, line up the receiver arm holes with the base
plate holes and use the sheet metal screws provided
(I) to secure the bracket (Fig. 1).
2. Connect house black wire to adaptor cable (D) black
wire, and house white wire to adaptor cable white
wire using the wire nuts (G) provided.
3. Thread adaptor cable and house ground wire through
center hole of mounting bracket (B) (Fig. 3).
4. Line up the holes on the mounting bracket (B) with
the holes on the junction box. Use either (2) #8
screws or (2) #10 screws (C) to attach the
mounting bracket (B) to the junction box (Fig. 3).
5. Attach fixture (A) ground wire and house ground
wire to mounting bracket ground screw (Fig. 3).
1
Instruction Manual/ Instrucciones
H. Optic Rotator Tool
G. (2) Wire Nuts
Herramienta para
(2) Tuercas
rotar la óptica
para alambre
1
2
Motion Activated
Eave Mount Only
Flood and Dusk to Dawn
Eave Mount or Wall Mount
3 Fixture
ground
D
D. Adapter Cable
Cable adaptador
I. #6 x 5/16 in. sheet
metal screws
Tornillos de metal
para chapas
N.° 6 x 5/16 pulg
Optional lock position
B
I
Mounting Options
Junction
box
B
C C