Best IP29M Serie Manual Del Usaurio página 14

21. OPERATION
(CONT'D)
Grease filter maintenance indicator
• After 30 hours of operation, the grease filter maintenance icon (item 5 on control illustration) appears. This means filters need to
be cleaned.
• Once the grease filter cleaning is done, press on grease filter reset push-button to reset the filter maintenance timer.
Interface backlighting
• Off mode (Blower off, Particulates sensor and Air refresh modes disabled): Backlighting is off.
• Halogen lighting activated: does not affect backlighting.
• Blower turns on: Backlighting at maximum intensity.
• Particulates sensor and Air refresh mode activated: Backlighting at maximum intensity.
• Particulates sensor at sensitivity settings and Air refresh in activated mode: Backlighting at minimum intensity.
HEAT SENTRY™
This hood is equipped with a HEAT SENTRY™ thermostat. This thermostat is a device that will start or speed up the blower if it senses
excessive heat above the cooking surface.
• If blower is OFF—it turns the blower to speed 3 (blower speed icon shows H).
• If blower is ON—it turns the blower up to speed 3 (blower speed icon shows H).
NOTE: When Heat Sentry™ is activated, Air refresh mode and Particulate sensor are inactivated. Also, communication coming
from the LinkLogic™ Module is disabled.
• When the temperature level drops to normal, the blower will return to its original setting (blower speed icon will show the original
blower speed).
• To turn off the blower when Heat Sentry™ is activated, press and hold the blower push-button (item 2 on illustration) for more
than 1 second.
LinkLogic™ Network compatibility
Your IP29M Series range hood can be linked to LinkLogic network, if installed in your house.
L L L I
INK OGIC INKING NSTRUCTIONS
A. A " "
CTIVATE THE LINK
Push the LinkLogic link mode push-button (item 4 on control illustration) for 2 seconds; the LinkLogic icon of the interface (item 11 on
control illustration) should be visible and backlighting is full intensity at that point.
L W R
INK FOR ALL EMOTE
R
OR EMOTE
A " "
CTIVATE THE LINK
Push the "link" button of the LinkLogic device for
a specific duration to activate its link mode
(see instructions of LinkLogic device).
S "A
TART THE UTO
Push the LinkLogic link mode push-button
(item 4 on illustration) to start the "Auto-Link" process,
flashing "A" should be visible (item 8 on control illustration)
on the interface until link is done.
NOTE: For some LinkLogic devices, no "A" will be flashing
because the linking duration is too short.
B. E
XIT LINK MODE OF THE HOOD
Press and hold LinkLogic link mode push-button (item 4 on control illustration) for 2 seconds to exit "link" mode. Link mode remains
activated for 4 minutes if no other operation is done.
MODE OF THE HOOD
C , R C
ONTROL EMOTE
B M
LOWER ODULES
L L
MODE OF THE INK OGIC DEVICE
-L "
INK PROCESS OF THE HOOD
L
INK OF ANOTHER
Go back to the appropriate first step if another LinkLogic device
needs to be linked. Otherwise, to exit "link" mode, go to
ONTROL
L
INK FOR
G
O TO STEP
BOARD JUMPERS BASED ON BLOWER PERFORMANCE
S
Push the LinkLogic master link mode push-button
(item 1 on illustration) to start the "Master Link" process,
flashing "L" should be visible (item 8 on control illustration) on
the hood interface, meaning that the hood is waiting for a
A
CTIVATE THE
(see instructions of device for location) for a specific duration to
activate its link mode. Wait for the "L" to disappear from the
L L
INK OGIC DEVICE
E
XIT LINK MODE OF THE HOOD
- 14 -
S S ™
MART ENSE OR
22 ( )
ON NEXT PAGE
"M "
TART THE ASTER LINK PROCESS OF THE HOOD
SmartSense™ or Make-Up Air module to link.
" "
LINK MODE OF THE
Push the "link" button of the LinkLogic device
hood interface to do next step.
.
M -U A M
AKE P IR ODULES
L L
TO CONFIGURE INK OGIC
.
L L
INK OGIC DEVICE