Hoshizaki IM-240DME Manual De Instalación página 2

1. In order to carry out safe and proper installation of the product,
please read this booklet carefully beforehand and follow the
instructions contained within.
2. On completion of the installation, start up the icemaker to
check for any abnormalities, and instruct the user on how to
use and maintain the icemaker in accordance with the
Instruction Manual.
3. This booklet should be handed over to the user after the
installation and be preserved by the user together with the
Instruction Manual for any further consultation that may be
necessary.
The installation must be carried out by qualified
personnel, in accordance with current regulations, according
to the manufacturer's instructions.
1. UNPACKING
Children should not be allowed in reach of the packaging elements
(plastic bags and expanded polystyrene) as they are potential
sources of danger.
Remove shipping carton, tape(s) and packing. If packing material
is left in the icemaker, it will not work properly.
Louver, Air Filter
(Air-cooled Model)
Front Panel
Handle
Note: This icemaker needs a Storage Bin. Hoshizaki recommends the
following Ice Storage Bins:
P-200SD -------- IM-240D
F650-44 -------- IM-240D/IM-480D
F950-48 -------- IM-480D/IM-720D
F1025-52 ------- IM-480D/IM-720D
1) After removing the packaging, make sure that the icemaker and the
Storage Bin are in good condition. If in doubt, please do not use the
equipment but apply to professionally qualified personnel. See the
instruction sheet attached to the Storage Bin for its unpacking and
installation guidelines.
2) Remove the icemaker panels to gain access to the accessory kit
and to assist easier installation.
[IM-240D]
a) Front Panel: Remove the screw(s). Lift up and pull toward you.
b) Top Panel: Remove the screw(s). Simply lift off.
c) Side Panel: Remove the screw(s). Slide forward slightly, and
then lift off.
d) Rear Panel: Does not require removal.
92E1CG20C0012
IMPORTANT
WARNING
WARNING
CAUTION
Top Panel
Power Cord
Condensing Unit
Bin Door
Storage Bin
(Optional)
Adjustable Legs
Fig. 1
[IM-240X]
Drain Outlet
(No top panel,
Drain Outlet on the left)
Fig. 2
3) Remove the package of accessories, and check the contents:
a) Installation Kit (Air-Cooled)
Inlet Hose
Outlet Hose
Installation Kit (Water-Cooled)
Inlet Hose
Outlet Hose
1/2-3/4 Nipple
b) Scoop (Except IM-240X)
c) Ice Chute (IM-240X only)
d) Drain Pipe Collar (IM-240X only)
e) Packing (IM-240X only)
4) Remove the shipping tape holding the Bin Control Switch.
5) Remove the protective plastic film from the exterior. If the icemaker
is exposed to the sun or to heat, remove the film after the icemaker
cools.
2. LOCATION
1. This icemaker is not intended for outdoor use. Normal operating
ambient temperature should be within 1°C to 40°C. Normal
operating water temperature should be within 5°C to 35°C.
Operation of the icemaker, for extended periods, outside of
these normal temperature ranges may affect production
capacity.
2. The icemaker should not be located next to ovens, grills or
other high heat producing equipment.
3. The location should provide a firm and level foundation for the
equipment.
4. Allow 15 cm clearance at rear, sides and top for proper air
circulation and ease of maintenance and/or service should
they be required. For air-cooled model only, allow 30 cm
clearance at the right side.
5. This appliance is not suitable for installation in an area where
a water jet could be used and where dripping is not allowed.
6. Do not place anything on top of the icemaker or in front of the
Louver.
7. This icemaker will not work at subfreezing temperatures. To
prevent damage to the water supply line, drain the icemaker
when air temperature is below zero.
3. INSTALLATION
* Incorrect installation can cause harm to
people, animals or things, for which the
m a n u f a c t u r e r c a n n o t b e h e l d
responsible.
1) Lay the Storage Bin on its rear side
carefully to prevent damage. Secure
the four adjustable legs (bin accessory)
into the four tapped holes on the
underside of the Bin. See Fig. 3.
2) Position the Storage Bin in the selected
permanent position, and level it in both
the left-to-right and front-to-rear
directions. See Fig. 4.
3) Remove the icemaker panels. The Rear
Panel is not required to be removed for
installation. See "1. UNPACKING".
4) Remove the shipping tape holding the Drain Pan.
5) Place the icemaker on the top of the Storage Bin. Be careful not to
damage the icemaker frame and the Bin Control Switch. See Fig. 5.
1
ENGLISH
1
1
2
2
2
1
1
1
1
IMPORTANT
Fig. 3
Adjustable Leg
Fig. 4
Bottom
Adjustable Leg