Safety Notes; Technical Data - Grohe Eurosmart Cosmopolitan E 36 334 Manual Del Usuario

GB

Safety notes

• Installation is only possible in frost-free rooms.
• The switched-mode power supply is only suitable for indoor
use.
• In the case of damage to the external connection cable of
the switched-mode power supply, the cable must be
replaced by the manufacturer or the manufacturer's
customer service department or an equally qualified person,
in order to prevent a hazard.
• Use only genuine replacement parts and accessories. The
use of other parts will result in voiding of the warranty and
the CE identification.

Technical data

• Flow rate at 0.3 MPa (3 bar) flow pressure:
• Voltage supply: 100-240 V AC 50-60 Hz/6.75 V DC
• Power consumption:
• Automatic safety shut-off:
(5 - 420 s adjustable)
• Run-on time (0 - 10 s adjustable):
• Reception range with Kodak Gray Card, grey
side, 8 x 10", landscape (factory setting):
Electrical test data
• Software class:
• Contamination class:
• Rated surge voltage
• Temperature of ball impact test
The test for electromagnetic compatibility (interference
emission test) was performed at the rated voltage and rated
current.
General functions
• Thermal disinfection:
• Remaining battery capacity:
Programme 1 functions (factory setting)
• Cleaning mode:
• Automatic flushing:
• Thermal disinfection time:
Further pre-set programmes can be selected via the sensor
system.
Special accessories
Further settings and special functions are available via the
infrared remote control (Prod. no. 36 206).
Approval and conformity
This product conforms to the requirements of the
relevant EU guidelines.
The conformity declarations can be obtained from the following
address:
GROHE Deutschland Vertriebs GmbH
Zur Porta 9
D-32457 Porta Westfalica
5
Installation
Plaster and tile the wall, excluding the area of the structural
shell protection.
1. Cut off inspection chamber (A) flush with tiles, see fold-out
page II, Fig. [1].
Flush pipes thoroughly before and after installation (observe
EN 806).
2. Attach upper part of switched-mode power supply (B) to
base (B1), see Fig. [2].
3. Fasten frame (C) using screws (D) and washers (D1),
see Fig. [3].
4. Fasten spout (E) to wall plate (G) using screw (F),
see Fig. [4].
5. Connect hose (H) to housing (I), see Fig. [5].
6. Connect plug-in connector between electronics and
solenoid valve, see Fig. [6].
approx. 9 l/min
7. Connect plug-in connector between electronics and
switched-mode power supply.
2.4 W
Open hot and cold water supply and check that connections
60 s
are watertight.
1 s
Temperature adjustment
approx. 13cm
(Only in conjunction with wall-mounting box 36 336)
1. Loosen screw (J) and remove cap (K), see Fig. [7].
A
2. The thermostatic cartridge is set to 38 °C at the factory.
2
The temperature is regulated by turning adjusting screw (L),
2500 V
see Fig. [8].
100 °C
3. Refit cap (K) and fasten using screw (J), see Fig. [9].
Final installation
1. Insert wall plate (G) from above in frame (C) and fasten
using screw (G1), see Fig. [10].
activatable
Operation
readable
The infrared electronics emit invisible, pulsed light.
The sensor system is adjusted so that water flow is initiated
activatable
when the hands approach the vicinity of the spout.
deactivated
When the hands are withdrawn from the vicinity of the spout,
3.5 min
water flow is stopped after 1 s (factory setting).
The range of the sensor system is dependent upon the
reflective properties of the detected object.
Automatic safety shut-off
After 60 s of continuous detection of an object, the infrared
electronics automatically stop the water flow.