Troubleshooting Roubleshooting - Thetford SANICON Turbo 500 Manual Del Propietário

Operation, cont'd.
Empty Gray Water Tank(S)
Refer to the Fig. 1.
1. Be sure universal nozzle (
station! Refer to "Attach to Dump Station" procedure.
TIP For Cleaner Storage: Emptying black water
NOTICE
tank fi rst, allows gray water to cleanse the
system.
2. Open gray water tank gate valve (
3. Turn pump on.
4. Do not leave unit unattended.
TIP: The hose expands as fl uid moves to dump
NOTICE
station and contracts when tank is empty.
5. Turn pump off.
6. Close gray water tank gate valve
7. Repeat Steps 2-6 for secondary gray tanks.
Gray water bypass is possible if the discharge
NOTICE
plumbing does not fl ow upward.
Prepare Hose For Storage
Refer to the Fig. 1.
1. Be sure pump is off.
TIP For Faster Draining: Leave gray gate valve
NOTICE
open allowing hose to vent and expediting
(L)
the process.
2. Drain discharge hose (
direct excess water into the dump station.
3. Disconnect universal nozzle (
4. Install cap(s) ( G, H ).
5. Return hose to coach hose compartment (
nected to coach.
Helpful Hints
■ Empty the black water fi rst. Use gray water to rinse the
hose after emptying the black water.
■ Additional hoses can be purchased from Thetford and used
to extend the length of the discharge hose. Connect the
hoses using 1.5 in. (3.8 cm) barbed coupling with clamp.
■ If you wish to extend the discharge hose, connect a 3/4
in (1.9 cm) inner diameter garden hose to the end of the
nozzle. Do not extend the hose beyond 150 ft. (45 m).
A longer discharge hose reduces fl ow rate.
NOTICE
■ Before storing the hose, make sure that all liquid has
drained from the hose.
Obstruction Removal
Be sure to have container available for captur-
NOTICE
ing system fl uid!
97539 Rev. B (07/10/2017)
F ) is securely attached to dump
L ).
(L) .
E ) by holding at a sloped angle to
F ) from dump station.
); leave hose con-
I
1. Be sure all contents have been drained from system. If
manual over-ride ( ) has been installed, remove bayonet cap,
J
and open gate valve (
Turn off power and remove pump fuse. Once the obstruc-
NOTICE AVISO DANGER AVIS
! ! ! ! ATTENTION ATENCIÓN CAUTION
tion is removed, there is potential injury to hands or
ATTENTION ATTENTION ATTENTION
fi ngers in the path of the impeller if the power is on!
2. Disconnect the power by removing the pump fuse or discon-
necting the battery.
3. Make sure all gate valves are closed.
Plumbing from the discharge port (
NOTICE
need to be disconnected.
4. Locate 3" rubber coupling and loosen the hose clamp closest
to the pump. The 3.5" pipe hanger may need to be loosened.
Do NOT remove pump housing. Obstruction MUST be
! ! ! ! NOTICE AVISO ATENCIÓN CAUTION DANGER AVIS
ATTENTION
removed through inlet.
ATTENTION ATTENTION ATTENTION
5. Remove the pump from the 3" rubber coupling.
6. Insert the pump inlet into 3.0" rubber coupling and tighten
hose clamp.
7. Check 3.5" (4" inner diameter) pipe hanger; tighten if loose.
8. Be sure manual over-ride bypass gate valve (
reattach bayonet cap.
9. Reconnect the power.
10. Operate system using gray water; check for leaks.
Manual Over-ride (Optional)
Optional installation. May not be installed on your unit.
NOTICE
1. Locate manual over-ride connection (
2. Connect 3" sewer hose (not supplied): one end to (
end to dump station.
3. Open manual over-ride gate valve
4. Open black water gate valve; allow contents to drain.
5. Close black water gate valve.
6. Open gray water gate valve; allow contents to drain.
7. Close gray water gate valve.
8. Close manual over-ride gate valve.
9. Disconnect and clean sewer hose.
10. Install Manual Over-ride Bayonet Cap (
Winterizing
1. Be sure all tanks are empty.
2. Pour RV antifreeze into the empty black water tank.
3. Turn on pump.
Be sure to have container available for captur-
NOTICE
ing system fl uid!
4. Run pump until the antifreeze begins to discharge from
universal nozzle ( F ).
5. Turn pump switch to the Off position.
6. Drain discharge hose (
remove excess water; return hose to storage position.
4
L ) to drain system contents.
L ) is closed;
); remove bayonet cap.
J
.
).
J
) by holding at a sloped angle to
E
®
Turbo - Model 500
SANICON
C ) may
J ), other