Tabla de contenido
Idiomas disponibles
Idiomas disponibles
Users in the U.S.A.
Pre-Installation Requirements for Canon Facsimile Equipment
A. Location
Supply a suitable table, cabinet, or desk for the machine. See "Specifi cations" in the e-Manual for specifi c
dimensions and weight.
B. Order Information
1.
A single telephone line (touch-tone or rotary) should be used.
2.
Order an RJ11-C telephone wall jack (USOC), which should be installed by the telephone company. If the
RJ11-C wall jack is not present, telephone/facsimile operation is not possible.
3.
Order a normal business line from your telephone company's business representative. The line should be a
regular voice grade line or an equivalent one. Use one line per unit.
DDD (Direct Distance Dial) line
-or-
IDDD (International Direct Distance Dial) line if you communicate overseas
NOTE
Canon recommends an individual line following industry standards, i.e., 2,500 (touch-tone) or 500 (rotary/pulse
dial) telephones. A dedicated extension off a PBX (Private Branch eXchange) unit without "Call Waiting" can be
used with your facsimile unit. Key telephone systems are not recommended because they send nonstandard
signals to individual telephones for ringing and special codes, which may cause a facsimile error.
C. Power Requirements
The machine should be connected to a standard 120 volt AC, three-wire grounded outlet only.
Do not connect this machine to an outlet or power line shared with other appliances that cause "electrical noise."
Air conditioners, electric typewriters, copiers, and machines of this sort generate electrical noise that often
interferes with communications equipment and the sending and receiving of documents.
Connection of the Equipment
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the rear
panel of this equipment is a label that contains, among other information, a product identifi er in the format of
US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company.
The REN (Ringer Equivalence Number) is used to determine the number of devices that may be connected to
a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in response to an
incoming call. In most, but not all areas, the sum of the RENs should not exceed fi ve (5.0).
To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact
the local telephone company. The REN for this product is part of the product identifi er that has the format US:
AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 10 is a REN of 1.0).
An FCC compliant telephone line cable and modular plug is provided with this equipment. This equipment is
designed to be connected to the telephone network or premise wiring using a compatible modular jack that is
Part 68 compliant.
This equipment may not be used on coin service provided by the telephone company. Connection to party lines
is subjected to state tariffs.
In Case of Equipment Malfunction
Should any malfunction occur which cannot be corrected by the procedures described in this guide or the
e-Manual, disconnect the equipment from the telephone line cable and disconnect the power cord.
The telephone line cable should not be reconnected or the power switch turned ON until the problem is
completely resolved. Users should contact Canon Authorized Service Facilities for servicing of equipment,
Information regarding Authorized Service Facility locations can be obtained by calling Canon Customer Care
Center (1-800-OK-CANON).
Rights of the Telephone Company
If this equipment (imageCLASS MF4570dn) causes harm to the telephone network, the telephone company
may temporarily disconnect service. The telephone company also retains the right to make changes in facilities
and services that may affect the operation of this equipment. When such changes are necessary, the telephone
company is required to give adequate prior notice to the user.
However, if advance notice is not possible, the telephone company will notify the customer as soon as possible.
Also, the customer will be advised of his/her right to fi le a complaint with the FCC if he/she believes it is
necessary.
WARNING
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other
electronic device, including FAX machines, to send any message unless such message clearly contains in a
margin at the top or bottom of each transmitted page or on the fi rst page of the transmission, the date and time
it is sent and an identifi cation of the business or other entity, or other individual sending the message and the
telephone number of the sending machine or such business, other entity, or individual.
(The telephone number provided may not be a 900 number or any other number for which charges exceed local
or long-distance transmission charges.)
NOTE
In order to program this information into your machine, you should complete the procedure for registering your
name, unit's telephone number, time, and date in the Starter Guide.
Users in Canada
Pre-Installation Requirements for Canon Facsimile Equipment
A. Location
Supply a suitable table, cabinet, or desk for the machine. See "Specifi cations" in the e-Manual for specifi c
dimensions and weight.
B. Order Information
1.
A single telephone line (touch-tone or rotary) should be used.
2.
Order a CA11A modular jack, which should be installed by the telephone company. If the CA11A jack is not
present, installation cannot occur.
3.
Order a normal business line from your telephone company's business representative. The line should be a
regular voice grade line or an equivalent one. Use one line per unit.
DDD (Direct Distance Dial) line
-or-
IDDD (International Direct Distance Dial) line if you communicate overseas
NOTE
Canon recommends an individual line following industry standards, i.e., 2,500 (touch-tone) or 500 (rotary/pulse
dial) telephones. A dedicated extension off a PBX (Private Branch eXchange) unit without "Call Waiting" can be
used with your facsimile unit. Key telephone systems are not recommended because they send nonstandard
signals to individual telephones for ringing and special codes, which may cause a facsimile error.
C. Power Requirements
The power outlet should be a three-prong grounded receptacle (Single or Duplex). It should be independent from
copiers, heaters, air conditioners, or any electric equipment that is thermostatically controlled. The rated value
is 115 volts and 15 amperes. The CA11A modular jack should be relatively close to the power outlet to facilitate
installation.
8
Tabla de contenido
