Electrical Connections; 3-Wire Branch Circuit; I W E R B A R C N H C C R I U T I; Final Checklist - Fulgor Milano F1SP24-1 Serie Manual Del Usaurio

ELECTRICAL CONNECTIONS

Be sure your appliance is properly installed and grounded
by a qualified technician. Ask your dealer to recommend a
qualified technician or an authorized repair service.
This appliance is manufactured with a green GROUND wire
connected to the oven chassis. After making sure that the
power has been turned off, connect the flexible conduit from
the oven to the junction box using a U.L. listed conduit
connector. Figures A and B and the instructions provided
below present the most common way of connecting the ovens.
Your local codes and ordinances, of course, take precedence
over these instructions. Complete electrical connections
according to local codes and ordinances
"WARNING" Risk of Electric Shock, frame grounded to
neutral of appliance through a link .
Grounding through the neutral conductor is prohibited for new
branch-circuit installations (1996 NEC); mobile homes; and
recreational vehicles, or in an area where local codes prohibit
grounding through the neutral conductor. For installations
where grounding through the neutral conductor is prohibited:
Disconnect the ground from the neutral at free end of
conduit;
Use grounding terminal or lead to ground unit; and
Connect neutral terminal or lead to branch circuit neutral in
usual manner.
Figure A

FINAL CHECKLIST

To prevent improper connections leading to damage of
electrical components and so voiding the warranty, the
following steps must be performed:
1. Check the electrical requirements and make sure you have
the correct electrical supply and that the oven is properly
grounded.
2. Turn on the power supply to the oven.
3. Check power at the junction box wires using a voltmeter
having a range of 0-250V.
If you have installed the oven for use on 240V supply,
you should find that the voltage reading between the black
and red wires (Line to Line) should be 220V to 240V.
If you have modified the oven(s) for use on 208V, the
voltage reading between the black and red wires should be
190 to 208V. V
4. Set the clock by following these steps:
Immediately turn [+/-] knob to set hours + [INC] or - [DEC] .
Press [+/-] knob again to change minutes.
Immediately turn [+/-] knob to set minutes + [INC] or - [DEC] .
3UHVV >@ NQRE RU ZDLW IRU D IHZ VHFRQGV WR FRQ¿UP
8
3-WIRE BRANCH CIRCUIT (for US only)
Refer to Figure A, where local codes allow the connection of
GROUND wire from the oven to the branch circuit NEUTRAL
wire (gray or white colored wire):
If local codes permit, connect the green GROUND wire
from the oven and the white wire from the oven to the
branch circuit NEUTRAL wire (gray or white colored wire).
Connect the red and black leads from the oven to the
corresponding HOT Wires in the junction box.
Connect the local codes and power supply codes using a
terminal.
The terminal uses a thing adapting to the wire of the cord.
4-WIRE BRANCH CIRCUIT (for US and CANADA)
Refer to Figure B:
Disconnect ground from neutral at free end of conduit.
Connect the green GROUND wire from the oven to the
GROUND wire in the junction box (bare or green colored wire).
Connect the red and black leads from the oven to the
corresponding HOT Wires in the junction box.
Connect the white wire from the oven to the NEUTRAL (gray or
white) wire in the junction box.
Connect the local codes and power supply codes using a
terminal.
The terminal uses a thing adapting to the wire of the cord.
Figure B
Clock is now set.
5. Test the bake mode by following this step:
Move cooking mode knob to "BAKE" position.
Cooling fan and oven lights will turn on, the preheat led will
start to blink.
A beep is sounded when the oven reaches the preset 350 °F
(175 °C) and the preheat light stop to blink.
Move the knob back to "OFF" position to stop cooking.
6. To check the other oven functions refer to the "Using the
Oven Controls" section of the USER MANUAL.
7. If the oven is working properly, turn off the power supply to
the oven.
8. Place the cover on the junction box and make sure the
cover is securely fastened and turn on the power to the
oven.
Leave these INSTALLATION instructions as well as the
Operating Instructions with the owner.
Installation Manual
ENGLISH
Important: Use twist-on connector
with square-wire spring
From power
supply
Or
From the oven
Square-wire spring
Terminal Block