Section 5. Wiring Options For Controlling Jandy; Watercolors Rgbw Led Lights; Wiring To An Aqualink ® Rs Control System; Wiring To A Time Clock - Jandy Pro Serie Manual De Instalación Y Funcionamiento

Page 8
ENGLISH
Section 5. Wiring Options for
Controlling Jandy Pro
Series WaterColors LED
Lights
NOTE
The Jandy Pro Series WaterColors RGBW LED
Lights will not operate properly with light dimmers. Do
not wire the Jandy Pro Series Lights to any dimming
circuitry.
To the extent allowed by code and capacity of the
electrical equipment, multiple Jandy Pro Series lights
may be controlled with a single switch so their colors will
always be synchronized.
Separate switches may be used to control the on/off
and color functions of each Jandy Pro Series light. It is
recommended that these switches be located next to each
other to facilitate simple color synchronization when
desired. All switches must be operated at the same time
to assure color synchronization. Otherwise, the lights will
work independently of each other.
5.1 Wiring to an AquaLink
System
The Jandy Pro Series WaterColors RGBW LED Lights
can be wired into the Jandy Pro Series AquaLink
control system to provide simplified operation of the
lights, as well as a means to synchronize the color change
function. Connect the lights to one of the auxiliary relays
in the Power Center.
NOTE
It is recommended to connect one light per relay so
each light can be controlled separately. However, up to
four lights can be connected on a single relay. If there
are more than four lights installed on one AquaLink RS
system, ensure there is more than one auxiliary relay
available in the Power Center.
Refer to Figures 2 and 3 to connect the Jandy Pro Series
Color Lights to the Power Center.
WARNING
RISK OF ELECTRICAL SHOCK OR
ELECTROCUTION, which could result in serious
injury or death.
A Ground Fault Circuit Interrupter
(GFCI) must be provided for 120 volt models. A
Ground Fault Circuit Interrupter (GFCI) for 120
Volt transformers should be used if required by the
transformer manufacturer or if required by the local
applicable code and/or Authority Having Jurisdiction
(AHJ). When a GFCI is used, the conductors on the
load side of the GFCI circuit shall not occupy conduit,
boxes, or enclosures containing other conductors
unless the additional conductors are also protected by
a GFCI. Refer to local codes for complete details.
Jandy Pro Series, WaterColors RGBW LED Lights
®
NOTE
5.2
The Jandy Pro Series WaterColors RGBW LED Lights
can be wired into a basic time clock to automatically turn
on the lights at a predesignated time. Refer to Figure 4 to
connect the lights into the time clock.
5.3
The Jandy Pro Series WaterColors RGBW LED Lights
can be wired into a switch to manually turn on/off the
lights. Refer to Figure 5 to connect the lights into the
switch.
Section 6. Jandy Pro Series
RS Control
®
6.1
Turn the light ON. The first time the light is turned on,
RS
®
the color sequence begins with the Alpine White. To
change the color, turn the light OFF and then ON within
three (3) seconds. Continue turning OFF and ON until
the desired light color mode is reached. See Table 1 for
the color mode sequence.
Table 1.
NOTE
|
Installation Manual
The Jandy Pro Series WaterColors Lights are available
in 120-volt and 12-volt versions. If installing a 12-volt
light, a NRTL certified 120-volt/12-volt step-down (AC)
transformer must be used. For more information about
12-volt installations, refer to Section 8 of this manual.

Wiring to a Time Clock

Wiring to a Switch

WaterColors RGBW
LED Light Operating
Instructions
To Operate the Light and Change
Colors
Jandy Pro Series WaterColors Lights
Sequence
Sequence Order
1 Alpine White
2 Sky Blue
3 Cobalt Blue
4 Caribbean Blue
5 Spring Green
6 Emerald Green
7 Emerald Rose
8 Magenta
9 Violet
10 Slow Color Splash
11 Fast Color Splash
12 America the Beautiful
13 Fat Tuesday
14 Disco Tech
When the light is turned OFF for more than seven (7)
seconds, it will remain in the color set that is currently
active. When the light is turned back ON, the light will
be on the same color set.
Color Modes