Installation Instructions - HoMedics BubbleSpa Elite Manual De Instrucciones E Información De Garantía

BubbleSpaElite Features
• 3 Massage programs with 3 speeds
Figure 1
• Steady massage option with 3 strengths: low, medium or high
Suction Cup
Hose
Control
• 60-Minute timer function
Unit
Mat
• Operate via Central Programming Unit or cordless remote control
• Lightweight, compact and portable
15 30 60 X
1 2 3 TIMER
PROGRAM MASSAGE
HI HI
SPEED MED POWER MED STRENGTH
LO LO

Installation Instructions

Remote
Holder
1. Remove the mat from its packaging and make sure all
necessary components are included: mat, remote control, hose
Figure 2
suction cup, control unit and hose (Fig. 1).
2. Be sure the control unit is unplugged and positioned on a sturdy surface
Connector
where it cannot fall or be pulled into the tub, preferably the floor.
Mat
3. To place the mat, first dampen tub surface with a slight amount
of water. This will help the adhesion of suction cups (on bottom
of mat) to bathtub floor (Fig. 2).
4. To connect the hose to the control unit, line up the arrow on the hose with
Mat
Bathtub Floor the unlock mark on the control unit. Insert the hose end (with raised
Suction
bead) into the control unit and turn counter clockwise to the lock position
Cups
(Fig. 3). The raised bead should be lined up with the channel when
Figure 3
inserted.
5. Insert the other end of the hose into the mat (Fig. 4). NOTE: Keep the
hose free from kinks which could constrict airflow.
6. Attach the hose to the side of the bathtub with the suction cup, which is
attached to the hose (Fig. 5). The suction cup will help to stabilize the
LOCK UNLOCK
hose, and should be attached along the upper edge of the bathtub.
UNLOCK LOCK
7. Plug unit into 120 volt electrical outlet.
Instructions for Use
Power:
Figure 4
• After plugging in the control unit, press the POWER button on the
control unit panel. The corresponding POWER LED will illuminate
(Fig. 6).
• Each function button on the control unit panel features a corresponding
LED, which will illuminate when in use.
15 30 60
X
3
TIMER MASSAGE
Remote Control:
HI HI
ED MED STRENGTH
O POWER LO
• All programming functions may also be utilized in a similar
fashion using the remote control.
4
Caution:
• The remote control is water-resistant only. If dropped into water,
it should be removed immediately. A remote control holder
Mat may move
is included to conveniently store your remote. Just dampen
when entering or
the suction cup and attach to the wall or side of the bathtub.
exiting bathtub.
• The remote is powered by two CR2032 3V batteries. For initial use,
Exercise caution.
you will need to insert the batteries. To insert or replace, use a coin
to turn the lock on back of remote. Take off cover and insert both bat-
teries, "+" side up. Set cover in place and turn to lock.
Timer Function:
Figure 5 • The bath mat has a timer function which allows you to choose from
15, 30 or 60 minutes.
• Press the TIMER button to activate the function, then select the
Attach as
close to rim
desired time by pressing the TIMER button until its corresponding
as possible
LED is illuminated.
• Timer can be used for both steady bubble massage and bubble
massage programs and can be operated by remote control.
Choose Bubble Massage Option:
Figure 6
• Your BubbleSpaElite offers you a choice of either steady massage
PRESS POWER BUTTON
action or three massage programs as follows:
ON CONTROL UNIT
Steady Bubble Massage:
• Press the MASSAGE button on the control unit. The low strength
15 30 60
X
LED will automatically illuminate.
1 2 3
TIMER
MASSAGE
PROGRAM
BubbleSpa Elite TM
• The massage speed may be increased or decreased by
HI HI
SPEED MED MED STRENGTH pressing the STRENGTH button repeatedly. The corresponding
POWER
LO
LO
LED for each strength level will illuminate when selected.
Bubble Massage Programs:
• Press the PROGRAM button on the control unit. The corresponding
LED will illuminate.
• You may choose any one of 3 programs by pressing the program
button until the desired program is selected. The speed may be
increased or decreased from low to high by pressing the SPEED
button repeatedly until the desired level is selected.
5