Technical Data; Noise Emission Levels; Before Using For The First Time - HERKULES STR 250 LED Manual De Instrucciones

Anleitung STR 250 LED_SPK7:Anleitung STR 250-1L_SPK1
GB
Never leave the machine unattended in rooms
with children.
Always pull out the power plug before examining
the electric motor compartment system
.

5. Technical data

Motor rating: 1500 W S2 20 min
Motor speed:
AC motor: 230 V ~ 50 Hz
Insulation material class:
Protection type:
Table size: 630 x 450 mm
Cut length :
Jolly length:
Max. workpiece thickness 90°:
Max. workpiece thickness 45°:
Diamond wheel: Ø 250 x Ø 25.4 mm
Weight:
LED light power supply: 3 x 1.5 V (AAA)
Load factor:
A load factor of S2 20 min (intermittent periodic
duty) means that you may operate the motor
continuously at its nominal power level (1500 W)
for no longer than the time stipulated on the
specifications label (20 minutes ON period).
If you fail to observe this time limit the motor will
overheat. During the OFF period the motor will
cool again to its starting temperature.

Noise emission levels

The noise emitted by this saw is measured in
accordance with EN ISO 3744; EN ISO 11201
The noise at the workplace may exceed 85 db
(A). The user will require noise protection
measures if this is the case. (Wear ear-muffs!)
No-Load operation
Sound pressure level L 94,5 dB(A)
pA
Sound power level L 107,5 dB(A)
WA
12

6. Before using for the first time

The machine must be set up so that it stands
firmly, i.e. it must be securely screwed to a work
bench, the base frame supplied in delivery, or
similar.
All covers and safety devices must be correctly
attached before the machine is used for the first
time.
The cutting wheel must rotate smoothly.
3000 rpm
Check that the voltage on the rating plate is the
same as your supply voltage before you connect
Class B
the machine to the power supply.
IP54
7. RCD plug (Fig. 16)
570 mm
570 mm
Connect the RCD plug (41) to the power supply.
Press the reset button (42) and the control lamp (43)
65 mm
will begin to shine. Press the test button (44) to
48 mm
check the function of the RCD plug. If everything is
working properly the control lamp (43) will go out and
54 kg
the contact to the power supply will be interrupted.
The RCD plug triggers at a fault current of 30 mA.
Defective RCD plugs must be replaced by a qualified
electrician.
Press the reset key (42) again in order to be able to
start up the machine.
8. Assembly and operation (Fig. 3/4/5)
8.1 Fitting the hose and cable guide (Fig. 17)
8.2 Assembly of the sub-frame and cooling water
pump (Fig. 2-4)
Secure the feet (1) to the water trough using the
thumb screws (12). The feet and the mountings
for them are each marked with numbers.
Turn the sub-frame upright.
Place the complete tile cutter into the trough (3).
Place the cooling water pump (13) in a suitable
position in the water trough and secure it to the
base of the trough with the suction cups. The
pump, cable and cooling water hose (14) must
not be able to get into the cutting area.
Fill with water until the pump (13) is completely
immersed in water.
Remove the star handle screw (11) and spacer
(40).
Important: Before you lift the machine out of the
trough or transport it, the cutting unit must be
secured again with the star handle screw (11) and
spacer (40).
07.12.2006 13:49 Uhr Seite 12