for diverting. Note: Shoes are to be assigned for the entire
length of the package plus one extra shoe is to be assigned to
the trailing end of the package.
3. . .
Check for the proper gap between packages for safe sorting. It
is important to check for the proper gap here, even if it has
been set prior to this point, to insure that the packages are
truly spaced properly. Attempting to sort packages with too
little gap between them can cause jams.Note:The minimum gap
necessary for sorting a package is a function of the width of the
package. The charts below should be used in checking for
proper gap.
ProSort 421 (22° Diverts)
ProSort 421 (22º Centros de Desvío)
0" < W ≤ 13" Minimum gap = 10"
13" < W ≤ 26" Minimum gap = 16"
26" < W ≤ 40" Minimum gap = 20"
* W = Package Width
Note:When sorting to both sides, the minimum gap from the above
charts must be increased by 6 in.
Jam/Confirmation Photo-eye—Photo-eyes mounted on
each take-away spur of the sorter, as close to the sorter as
possible.These eyes perform two functions:
1. . .
Detect a product jam at the sorter "exit point." If a package
blocks this photo-eye for a longer time than it would take
for the package to travel past the photo-eye normally, this
indicates that the package is jammed.The sorter should be
stopped and the jam cleared before restarting the sorter.
2. . .
Divert confirmation. If a divert signal is given to a particular
divert point, and no package is detected by the associated
jam/confirmation photo-eye, an error has occurred. The
sorter should be stopped and the error found and
corrected before restarting the sorter.
Full Line Photo-eye—Photo-eyes mounted on each divert
lane from the sorter, near the infeed end of that lane.These eyes
are used to signal the system controls that a particular divert lane
is full. The controls should then send any further packages
assigned to that lane to the recirculation line until the full line
photo-eye on that lane no longer indicates the full condition.
entre ellos puede causar obstrucciones. Nota: El mínimo espacio
necesario para la clasificación de un paquete está en función del
ancho del mismo. Las siguientes tablas deben considearse al
asignar el gap apropiado.
ProSort 431 (30° Diverts)
ProSort 431 (30º Centros de Desvío)
0" < W ≤ 10" Minimum gap = 10"
10" < W ≤ 20" Minimum gap = 16"
20" < W ≤ 30" Minimum gap = 20"
30" < W ≤ 40" Minimum gap = 26"
* W = Ancho del Paquete
Minimum gap = Espacio mínimo
Nota: Cuando se clasifica hacia ambos lados, el espacio mínimo en la tabla
debe incrementarse en 6 pulgadas.
Foto celda de Confirmación/Obstrucción—Las foto celda se
coloca en las espuelas acopladas al sorter lo más cerca posible al mismo.
Esta foto celda tiene dos funciones:
1. . .
Detectar un producto atorado en el punto de salida del sorter.
Si un paquete bloquea esta foto celda por más tiempo de lo que
le tomaría a este viajar y pasar la foto celda normalmente, esto
indica que el paquete se encuentra atorado. El sorter debe ser
detenido y la obstrucción removida antes de volver lo a poner en
marcha.
2. . .
Confirmación de desviación. Si una señal de desviación es dada
para un punto particular de desviación ningún paquete es
detectado por la foto celda asociada, un error ha ocurrido. El
sorter debe ser detenido y el error detectado y corregido antes
de ponerlo en marcha.
Foto celda de Línea Llena—Las foto celdas que son montadas en
las líneas desviadoras del sorter, lo más cerca posible al extremo
alimentador de las mismas, se encargadas de dar una señal a los
controles del sistema cuando una línea particular desviadoras está
llena. Los controles harán que los paquetes asignados a esta línea
recirculen hasta que la foto celda deje de indincar que la línea se
encuentra llena.
19