Listening Through A Receiver (Home Theater); Service - Samsung HP-T4254 Manual Del Proprietário

Listening through a Receiver (Home theater)
You can listen to sound through a receiver instead of the TV speaker.
1 Press the Anynet + button.
Press the A or T button to select Receiver, then press the ENTER button.
2 Press the 4 or I_ button to select to On, then press the ENTER button.
Now you can listen to sound through the receiver.
3 Press the EXIT button to exit.
When the receiver is set to On, you can listen to the TV sound through the 2-channel(Stereo)
Sound. This is not always true. When TV is displaying DTV(air) TV can send out 5.1 channet
sound through SPDIF. But when the source is DVD(for example), TV can receive only 2 channel sound using HDMI.
In that case, 2 channel sound is only transmitted to the Receiver through SPDIF.
_-- If the receiver is exclusively for a home theater only (supporting audio only), it may not appear in the device list.
Only when you have connected the optical jack of the TV and the receiver properly, does Receiver work.
In case of a content with copyright problem, listening through the receiver may not properly operate.
_-- When listening through the receiver, there are restrictions for using the PIP and audio-related menu.
Check Points before Requesting Service
Symptom Solution
Anynet + does not work. [] Check if the device is an Anynet+ device. The Anynet+ system supports Anynet+ devices
only.
[] Connect only one receiver (home theater).
[] Check if the Anynet+ device power cord is properly connected.
[] Check theAnynet + device's Video/Audio/HDMI 1.3 cable connections.
[] Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
[] Check whether the TV remote control is in TV mode.
[] Check whether it isAnynet+ exclusive remote control
[] Anynet+ doesn't work at a certain condition. (Searching channels)
[] When connecting or removing the HDMI 1.3 cable, please make sure to search devices
again or restart your TV.
[] Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet +. [] Check if the Anynet+ device is properly connected to the TV and check if the Anynet+
(HDMI-CEC) is set to On in the Anynet + Setup menu.
[] Press the TV button on the TV remote control to switch to TV. Then press the Anynet +
button to show the Anynet + menu and select a menu you want.
I want to exit Anynet +. [] Select View TV in Anynet+ menu.
[] Press the SOURCE button on the TV remote control and select a device other than
Anynet + devices.
[] Press any of CH, CH LIST, PRE-CH, and FAV.CH to change to the TV mode.
(Note that the channel button operates only when an Anynet + device with a built-in tuner
is not connected.)
The Connecting to Anynet + device... [] You cannot use the remote control when you are configuring Anynet + or switching to a
message appears on the screen, view mode.
[] Use the remote control when the Anynet + setting or switching to view mode is complete.
The Anynet + device does not play. You cannot use the play function when Plug & Play is in progress.
The connected device is not [] Check whether or not the device supports Anynet + functions.
displayed. [] Check whether or not the HDMI 1.3 cable is properly connected.
[] Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu.
[] SearchAnynet+ devices again.
[] You can connect an Anynet+ device using the HDMI 1.3 cable only. Some HDMI cables
+
may not support Anynet functions.
Check whether the antenna jack on the recording device is properly connected.
Connect the optical cane between TV and the receiver.
The TV program cannot be
recorded.
The TV sound is not output through
the receiver.