Display Messages - RedFuel SL1 Manual Del Usuario

9.2 POWERING A 12V DC DEVICE (up to 6A)
The Fuel Pack is a power source for all DC
accessories that are equipped with a 12V
accessory plug.
NOTE: Do not power a DC device with
the unit while charging the internal battery.
1. Make sure the device to be powered
is OFF before inserting the 12V DC
accessory plug into the 12V DC outlet.
2. Plug the 12V port adaptor into the unit's
12V output port.
3. Press the
4. Plug your device into the 12V adaptor
port and turn on the device (if required).
5. When finished, turn off the DC device
(if required) and disconnect the device.
Press any button, to turn on the display.
Then press the
12V function.
NOTE: Extended operation of a DC device
may result in excessive battery drain.
6. Recharge the Fuel Pack immediately
after unplugging the device.
9.3 USING THE USB PORT
The USB port provides up to 2A at 5V DC.
1. Press the

10. DISPLAY MESSAGES

Messages during recharge:
CHARGING - XX% (Green LED lit) –
Plugged into the AC outlet and internal
battery is recharging .
FULLY CHARGED (Green LED pulsing) –
Plugged into the AC outlet and internal
battery is completely charged.
BATTERY TOO HOT TO CHARGE –
The temperature of the internal battery
is too high.
BATTERY TOO COLD TO CHARGE –
The temperature of the internal battery is
too low.
CHARGING - USB ON – The USB
function is in use while the internal battery
is recharging.
CHARGING - 12V ON – The 12V function
is in use while the internal battery is
recharging.
FULLY CHARGED - USB ON – The
internal battery is fully charged and the
USB is in use.
FULLY CHARGED - 12V ON – The
internal battery is fully charged and the
12V port is in use.
UNPLUG CHARGER – Attempting to use
the jump starter while the unit is recharging.
button on the unit, twice.
button, to turn off the
button on the unit.
2. Plug the USB connector into the USB
port of the unit.
3. Plug the other (micro) end of the adaptor
into your device. Turn device on, if
necessary.
4. When finished using the USB port, turn
off the device (if necessary) and unplug
the device. Press any button, to turn
on the display. Then press the
twice, to turn off the USB function.
5. Recharge the unit.
NOTE: The USB power will automatically
turn off if not used for 10 minutes.
9.4 USING THE LED LIGHT
1. Press the
• once – for steady light
• twice – for a flashing light
2. When finished using the light, press the
button again, to turn off the light.
9.5 USING A MEMORY SAVER (not included).
The unit can be used with a memory saver
to save the vehicle's on-board diagnostic
computer settings (radio programs,
diagnostic codes, etc.) while the battery is
disconnected from the vehicle during repair
or maintenance. We recommend the SEC-
12V-OBD or OBD-L memory savers.
Messages during use of 12V/USB:
USB ON BATTERY XX% – The USB
port is in use. The % shows the battery's
M
charge.
12V ON BATTERY XX% – The 12V port
is in use.
USB/12V OVERLOAD – The 12V/USB
port is overloaded.
BATTERY LOW RECHARGE – While
using the 12V/USB, the battery voltage
has dropped below 12.5V. (4 beeps will
sound.) 12V/USB power will shut off after
5 minutes.
Messages during use of jump starter:
xx.xV – Clamps are connected to a car
battery, but jump start button was
not pressed.
CONNECT CLAMPS-BATTERY XX% –
Plugged into the AC outlet without the
clamps connected to a battery.
WARNING CLAMPS REVERSED
(alarm sounds) – The clamps are
connected backwards to a battery.
BATTERY LOW RECHARGE – The jump
start button has been pressed, and the
internal battery is below 9.6V (will beep).
OFF – The jump start button has been
pressed twice.
• 7 •
button
button: