Honeywell FocusPRO TH6000 Serie Guia De Instalacion página 4

Installation Guide
Wiring
Wiring guide — conventional systems
Shaded areas below apply only to
1H/1C System
(1 transformer)
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor
C 24VAC common
W Heat relay
G Fan relay
Heat-only System
Rc Power [1]
R [R+Rc joined by jumper]
C 24VAC common
W Heat relay
Heat-only System
(Series 0) [5]
Rc [R+Rc joined by jumper]
R Series 20 valve terminal "R"
Series 20 valve terminal "W"
Y
C 24VAC common
W Series 20 valve terminal "B"
Heat-only System
(normally open zone valve)
Rc [R+Rc joined by jumper]
R Power [1]
Y Normally open zone valve
C 24VAC common
1H/1C System
( transformers)
Rc Power (cooling transformer)
R Power (heating transformer)
Y Compressor contactor
C 24VAC common
W Heat relay
G Fan relay
NOTES
Wire specifications:
Use 18- to 22-gauge thermostat wire.
Shielded cable is not required.
[1] Power supply. Provide disconnect means and
overload protection as required.
[2] Remove jumper for 2-transformer systems.
[3] Optional 24VAC common connection.
[4] Common connection must come from cool-
ing transformer.
[5] In Installer Setup, set system type to Heat Only.
[6] In Installer Setup, set system type to 2Heat/
2Cool Conventional.
TH6320U/TH6220D
G W C Y R Rc
W C R Rc
[3]
G W C Y R Rc
W C Y R Rc
G W C Y R Rc
W C R Rc
C Y R Rc
[3]
W C R Rc
G W C Y R Rc
W C Y R Rc
G W C Y R Rc
W C Y R Rc
W C R Rc
G W C C Y Y R R Rc Rc
[1]
C Y R Rc
[3]
W C Y R Rc
G W C Y R Rc
W C R Rc
G W C Y R Rc
[5]
C Y R Rc
W C Y R Rc
G W C Y R Rc
C Y R Rc
[3]
G W C Y R Rc
[1, 2]
[1, 2]
[3, 4]
or as otherwise noted.
Heat-only System
with Fan
G W C
G W C Y R Rc
Rc Power
R [R+Rc joined by jumper]
C 24VAC common
G C
W C R Rc
W Heat relay
G W C Y R Rc
G Fan relay
G W C
Cool-only System
Y2 W2 G W C
W C Y R Rc
W C R Rc
Rc Power
G W C
G W C Y R Rc
R [R+Rc joined by jumper]
G C
Y Compressor contactor
Y2 W2 G W C
C Y R Rc
C 24VAC common
W C Y R Rc
G C
G W C Fan relay R Rc
G W C
Y2 W2 G W C
2H/2C System
G W C Y R Rc
[6]
(1 transformer) C Y R Rc
Y2 W2 G W C
W C Y R Rc
G W C Y R Rc Y2 W2 G W C
Rc Power G G W C C
R [R+Rc joined by jumper]
Y Compressor contactor (stage 1)
G W C Y R Rc
Y2 W2 G W C
C Y R Rc
C 24VAC common
Y2 W2 G W C
W C R Rc
G C
W Heat relay (stage 1)
G Fan relay
W2 Heat relay (stage 2)
G W C Y R Rc
Y2 W2 G W C
W C Y R Rc
Y2 W2 G W C
Y2 Compressor contactor (stage 2)
2H/2C System
( transformers) [6]
C Y R Rc
Y2 W2 G W C
Rc Power (cooling transformer)
R Power (heating transformer)
Y Compressor contactor (stage 1)
G W C Y R Rc
C 24VAC common
W Heat relay (stage 1)
G Fan relay
W2 Heat relay (stage 2)
Y2 Compressor contactor (stage 2)
See [notes] below
[7] In Installer Setup, set changeover valve to O
or B.
[8] In Installer Setup, set system type to 2Heat/
1Cool Heat Pump.
[9] In Installer Setup, set system type to 2Heat/
2Cool Heat Pump.
[10] In Installer Setup, set system type to 3Heat/
2Cool Heat Pump.
[11] L terminal sends a continuous output when
thermostat is set to Em. Heat. Connect to
Honeywell zoning panels to switch the panel
to Emergency Heat.
[12] Install field jumper between Aux and E if
there is no emergency heat relay.

R Rc
G W
[1]
[3]
Y R Rc
G
G W
R Rc
Y R Rc
Y2 W2 G W
[1]
R Rc G
G W
Y R Rc
Y R Rc
Y2 W2 G W
[3]
Y2 W2 G W
Y R Rc
G
R Rc
Y R Rc
Y2 W2 G W
Y R Rc
Y2 W2 G W
G W Y R Rc
[1] Y R R Rc Rc
Y R Rc
Y2 W2 G W
[3]
Y R Rc
G
Y R Rc
Y R Rc Y2 W2 G W
Y R Rc
Y2 W2 G W
Y R Rc
[3, 4]
C R Rc
C Y R Rc
C R Rc
C Y R Rc
C Y R Rc
C R Rc
C Y R Rc
C Y R Rc
C Y R Rc
C Y R Rc
C Y R Rc
C R Rc
C Y R Rc
C Y R Rc
C Y R Rc
C Y R Rc
[1, 2]
[1, 2]