Tabla de contenido
Idiomas disponibles
Idiomas disponibles
PRODUCT
SPECIFICATIONS
Pressure
Washer
Specifications
Pressure ...................
2,400 PSI
Flow Rate ..................
2.2 GPM
Chemical Mix ...............
Use as directed
Water Supply Temperature .....
Not to Exceed 140°F
Engine
Specifications
Rated Horsepower
...........
6.0 HP
Spark Plug Type: ...........
Champion RJ19LM
or Equivalent
Set Gap To: .............
0.030 inches
(0.760ram)
Gasoline Capacity ............
1.6 Quarts
Oil Above 40°F
.............
SAE 30
0°F - 40°F ...............
SAE 5W-30 orl0W-30
GENERAL
RECOMMENDATIONS
The pressure washer's warranty does not cover items
that have been subjected to operator abuse or
negligence. To receive full value from the warranty,
the operator must maintain pressure washer as
instructed in this manual.
Some adjustments will need to be made periodically to
properly maintain your pressure washer.
All service and adjustments should be made at least
once each season. Follow the requirements
in the
"Maintenance Schedule" chart above.
NOTE: Once a year you should clean or replace the
spark plug and replace the air filter. A new spark plug
and clean air filter assure proper fuel-air mixture and
help your engine run better and last longer.
BEFORE
EACH USE
•
Check engine oil level.
•
Check water inlet screen for damage.
•
Check high pressure hose for leaks.
•
Check chemical filters for damage.
•
Check spray gun and nozzle extension assembly
for leaks.
•
Purge pump of air and contaminants.
PRESSURE
WASHER
MAINTENANCE
Check
and Clean
Inlet Screen
Examine garden hose inlet screen. Clean if it is
clogged or replace if it is torn.
Check
High Pressure
Hose
High pressure hoses can develop leaks from wear,
kinking, or abuse. Inspect hose before each use.
Check for cuts, leaks, abrasions, bulging of cover, or
damage or movement of couplings. If any of these
conditions exist, replace hose immediately.
_
ANGER:
Never repair a high pressure hose.
Replace with hose that exceeds the maximum
pressure rating of your pressure washer.
Check
Gun and Nozzle Extension
Examine hose connection to spray gun and make sure
it is secure. Test trigger by pressing it and making
sure it springs back into place when you release it. Put
safety latch in UP position and test trigger. You should
not be able to press trigger. Replace spray gun
immediately if it fails any of these tests.
Check
In-Line Filter
Refer to the illustration and service the in-line filter if it
becomes clogged, as follows:
Nozzle Extension
In-line Filter
O-ring
1. Detach spray gun from high pressure hose. Detach
nozzle extension from spray gun and remove o-ring
and screen from nozzle extension. Flush the
screen, spray gun, and nozzle extension with clean
water to clear debris.
2. If the screen is damaged, the o-ring kit contains a
replacement in-line filter screen and an o-ring. If
undamaged, reuse screen.
3. Place the in-line filter screen into the threaded end
of the nozzle extension. Direction does not matter.
Push the screen in with the eraser end of a pencil
until it rests flat at the bottom of the opening. Take
care to not bend the screen.
4. Place the o-ring into the recess. Push the o-ring
snugly against the in-line filter screen.
5. Assemble the nozzle extension to the spray gun,
as described earlier in this manual.
Purge Pump of Air and Contaminants
To remove air from the pump, follow these steps:
•
Set up the pressure washer as described in the
ASSEMBLY section and connect the water supply.
•
Pull the trigger on the spray gun and hold until a
steady stream of water appears.
To remove contaminants from the pump, follow these
steps:
•
Set up the pressure washer as described in the
ASSEMBLY section, and connect the water supply.
•
Remove the nozzle extension from the spray gun.
•
Start the engine according to instructions in
OPERATION section.
•
Disengage the safety latch and pull the trigger on
the spray gun and hold.
10
Tabla de contenido
