Tools And Parts; Location Requirements; Product Dimensions - ELICA EPR628SS Guía De Instrucciones Para Instalación

Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed (all models)
■ Level
■ Drill
■ ¹⁄ " (3.0 mm) drill bit
8
■ Pencil
■ Pliers
■ Tape measure or ruler
■ Caulking gun and weatherproof caulking compound
■ Flat-blade screwdriver
■ Phillips screwdriver
■ Saber or keyhole saw
■ Metal snips
■ Vent clamps
Parts Supplied
Remove parts from packages. Check that all parts are included.
■ 1 - 30" x 12" (76.2 x 30.5 cm) face panel
■ Damper
■ 2 - 40W incandescent lamps (only model EAS428SS)
■ 2 - 50W halogen lamps (only model EPR628SS)
■ 2 - Metal grease filters
■ 2 - Mounting brackets
■ 2 - Metal spacers (for use when cabinet depth is greater
than 12")
■ Hardware package. Includes:
• Installation Instructions and Use and Care Guide
• 8 - metal washers
• 8 - plastic washers
• 8 - 4.5 x 13 mm wood screws
• 2 - 4.2 x 15 mm machine screws
• 4 - 3.5 x 9.5 mm flat-head sheet metal screws
• 8 - 4.2 x 19 mm sheet metal screws
• 6 - 3.5 x 9.5 mm sheet metal screws
• T10 TORX®† adapter
Parts needed
■ 6" (15.2 cm) round metal vent system
†®TORX is a registered trademark of Saturn Fasteners, Inc.

Tools and Parts

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.
Have a qualified technician install the range hood. It is the
installer's responsibility to comply with installation clearances
specified on the model/serial rating plate. The model/serial rating
plate is located inside the liner behind the filter on the left wall of
the range hood.
Range hood location should be away from strong draft areas,
such as windows, doors, and strong heating vents.Cabinet open-
ing dimensions that are shown must be used. Given dimensions
provide minimum clearance. Consult your cooktop/ range manu-
facturer installation instructions before making any cutouts.
Grounded electrical outlet is required. See "Electrical Require-
ments" section.
The range hood is factory set for vented installations through the
roof or wall. For non-vented (recirculating) installations see "Non-
Vented (recirculating) Installation Through the Soffit/Cabinet" in
the "Prepare Location" section. Recirculation Kit Part is available
from your dealer or an authorized parts distributor. All openings
in ceiling and wall where range hood will be installed must be
sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR, Part 328 (formerly the Federal Standard for Mobile Home
Construction and Safety, title 24, HUD, Part 280) or when such
standard is not applicable, the standard for Manufactured Home
Installation 1982 (Manufactured Home Sites, Communities and
Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local
codes.

Product Dimensions

I* - Metallic spacers
Spacers has to be installed
and used when cabinet depth
is greater than 12".
4
EAS428SS / EPR628SS range hood models
DIM A 28
DIM B
DIM C
DIM D 10 ¾" (27.3 cm)
DIM E 9 ½" (24.2 cm)
DIM F
DIM G 14
DIM H
DIM I
I*
I*
Dimension
⁄ " (71.8 cm)
1
4
26" (66 cm)
1 ⅛" (2.9 cm)
⁄ " (.85 cm)
5
16
⁄ " (37 cm)
9
16
6" (14.8 cm)
½" (1.27 cm)