Makita DFT023F Manual De Instrucciones página 8

Function
D ouble-h itting d etec tion
Maintenanc e alarm
A larm f or unav ailable
d ata c ommunic ation
( w ith th e tool in c onnec -
tion w ith P C )
I nd ic ation th at d ata c om-
munic ation is av ailable
( w ith th e tool in c onnec -
tion w ith P C )
Adjusting the fastening torque
W h en y ou w is h to d ri v e ma c h ine s c re w s, h e x bolts,
et c . w it h t h e pre d etermine d tor q ue, a d j ust t h e f astening
tor q ue as f ollo w s.
1. O pen t h e c h ange plate b y h an d so t h at y ou c an
see a h ole.
Fig.7: 1. C h ange plate
2.
P ull t h e s w it c h trigger an d release it so t h at t h e
a d j ust ring rotates an d t h e h ole be c omes v isible. A n d
t h en remo v e t h e batter y c artri d ge.
3. U se an optional a d j ust grip to a d j ust t h e f astening
tor q ue. I nsert t h e pin o f t h e a d j ust grip into t h e h ole
in t h e f ront o f t h e tool. A n d t h en, turn t h e a d j ust grip
c lo c k w ise to set a greater f astening tor q ue, an d c oun-
ter c lo c k w ise to set a smaller f astening tor q ue.
Fig.8: 1. A d j ust grip 2. H ole f or a d j ust grip
4. I nsert t h e batter y c artri d ge an d be sure t h at a
f astening tor q ue h as been set up b y using a f astening
tor q ue tester.
5. C lose t h e c h ange plate b y h an d se c urel y .
Adjusting no-load speed and
revolution angle etc.
Y ou c an a d j ust t h e no-loa d spee d , number o f turn, et c .
o f t h e tool w it h y our c omputer. I nstall t h e appli c ation
so f t w are in y our c omputer an d c onne c t it to t h e tool w it h
an U S B c able.
Fig.9: 1. U S B port 2. U S B c o v er 3. U S B c able
NOTICE:
Make sure t h at t h e U S B c o v er c lose d
w h en f astening.
NOTE: F or t h e appli c ation so f t w are, please c onta c t
Makita sales representati v e.
Status of the tool
W h en th e operator starts L igh ts up in red .
to re-f asten an alread y -f as-
tened sc rew , th e tool
d etec t it and stops.
A maintenan c e time h as c ome F lic kers in y ellow .
a c c or d ing to y our preset
number o f s c re w s d ri v en.
D ata c annot be F lic kers in y ellow .
ex c h anged betw een th e
tool and P C in spite of
th e c onnec tion.
T h e tool is c onnec ted to F lic kers in green.
P C and d ata c ommuni-
c ation is av ailable.
Status of the LED indicator/beeper
LED indicator
A long beep
ASSEMBLY
CAUTION:
switched off and the battery cartridge is removed
before carrying out any work on the tool.
Installing or removing driver bit/
socket bit
Fig.10
U se onl y d ri v er bit / so c ket bit t h at h as inserting portion
shown in the figure. Do not use any other driver bit/
so c ket bit.
For tool with shallow driver bit hole
A = 1 2mm
B= 9 mm
For tool with deep driver bit hole
A = 1 7mm
B= 1 4 mm
A = 1 2mm
B= 9 mm
Fig.11: 1. D ri v er bit 2. S lee v e
T o install t h e d ri v er bit, pull t h e slee v e in t h e d ire c tion o f
t h e arro w an d insert t h e d ri v er bit into t h e slee v e as f ar
as it w ill go.
T h en release t h e slee v e to se c ure t h e d ri v er bit.
T o remo v e t h e d ri v er bit, pull t h e slee v e in t h e d ire c tion
o f t h e arro w an d pull t h e d ri v er bit out.
NOTE: I f t h e d ri v er bit is not inserte d d eep enoug h
into t h e slee v e, t h e slee v e w ill not return to its original
position an d t h e d ri v er bit w ill not be se c ure d . I n t h is
c ase, tr y re-inserting t h e bit a c c or d ing to t h e instru c -
tions abo v e.
NOTE: When it is difficult to insert the driver bit, pull
t h e slee v e an d insert it into t h e slee v e as f ar as it w ill
go.
NOTE: A f ter inserting t h e d ri v er bit, make sure t h at it
is firmly secured. If it comes out, do not use it.
8 ENGLISH
Action to be taken
Beeper
– R eset th e alarm w ith th e
applic ation sof tw are.
– R estart th e applic ation
sof tw are and re-c onnec t
th e U S B c able.
–
Always be sure that the tool is
U se only th ese ty pe of d riv er
bit. F ollow th e proc ed ure
1 . ( Note) Bit-piec e is not
nec essary .
T o install th ese ty pes of d riv er
bits, f ollow th e proc ed ure 1 .
T o install th ese ty pes of d riv er
bits, f ollow th e proc ed ure 2.
( Note) Bit-piec e is nec essary
f or installing th e bit.
–
–