Makita DDF483 Manual De Instrucciones página 8

ASSEMBLY
CAUTION:
Al w ays be sure that the tool is
s w itched off and the battery cartridge is removed
before carrying out any w ork on the tool.
Installing or removing driver bit/
drill bit
For Model DDF483 (optional accessory)
Fig.9: 1. S l e e v e 2. C l o s e 3. O p e n
Turn the sleeve counterclockwise to open the chuck
jaws. Place the driver bit/drill bit in the chuck as far
as it will go. Turn the sleeve clockwise to tighten the
chuck. To remove the driver bit/drill bit, turn the sleeve
counterclockwise.
Installing or removing driver bit/
socket bit
For Model DDF083 (optional accessory)
Fig.10
Use only driver bit/socket bit that has inserting portion
shown in the figure. Do not use any other driver bit/
socket bit.
For tool w ith shallo w driver bit hole
A mm
B mm
For tool w ith deep driver bit hole
A 7mm
B mm
A mm
B mm
. To install the driver bit, pull the sleeve in the direc-
tion of the arrow and insert the driver bit into the
sleeve as far as it will go.
Then release the sleeve to secure the driver bit.
Fig.11: 1. Driver bit 2. S l e e v e
. To install the driver bit, pull the sleeve in the direc-
tion of the arrow and insert the bit-piece and driver
bit into the sleeve as far as it will go. The bit-piece
should be inserted into the sleeve with its pointed
end facing in. Then release the sleeve to secure
the driver bit.
Fig.12: 1. Driver bit 2. B i t - p i e c e 3. S l e e v e
To remove the driver bit, pull the sleeve in the direction
of the arrow and pull the driver bit out.
NOTE: If the driver bit is not inserted deep enough
into the sleeve, the sleeve will not return to its original
position and the driver bit will not be secured. In this
case, try re-inserting the bit according to the instruc-
tions above.
NOTE: After inserting the driver bit, make sure that it
is firmly secured. If it comes out, do not use it.
Use only these type of driver
bit. Follow the procedure
1. ( N o t e ) B i t - p i e c e i s n o t
n e c e s s a r y .
To install these types of driver
bits, follow the procedure .
To install these types of driver
bits, follow the procedure .
( N o t e ) B i t - p i e c e i s n e c e s s a r y
for installing the bit.
Installing hook
Fig.13: 1. G r o o v e 2. H o o k 3. S c r e w
The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool. To install
the hook, insert it into a groove in the tool housing on
either side and then secure it with a screw. To remove,
loosen the screw and then take it out.
Installing driver bit holder
Optional accessory
Fig.14: 1. Driver bit holder 2. Driver bit
Fit the driver bit holder into the protrusion at the tool foot
on either right or left side and secure it with a screw.
When not using the driver bit, keep it in the driver bit
holders. Driver bits 5 mm-long can be kept there.
OPERATION
CAUTION:
Al w ays insert the battery cartridge
all the w ay until it locks in place. If you can see the
red indicator on the upper side of the button, it is not
locked completely. Insert it fully until the red indicator
cannot be seen. If not, it may accidentally fall out of
the tool, causing injury to you or someone around
you.
CAUTION:
W hen the speed comes do w n
extremely, reduce the load or stop the tool to
avoid the tool damage.
old the tool firmly with one hand on the grip and the
other hand on the bottom of the battery cartridge to
c o n t r o l t h e t w i s t i n g a c t i o n .
Fig.15
Screw driving operation
CAUTION:
Adjust the adjusting ring to the
proper torque level for your w ork.
CAUTION:
Make sure that the driver bit is
inserted straight in the scre w head, or the scre w
and/or driver bit may be damaged.
Place the point of the driver bit in the screw head and
apply pressure to the tool. Start the tool slowly and then
increase the speed gradually. Release the switch trigger
as soon as the clutch cuts in.
NOTE: W h e n d r i v i n g w o o d s c r e w , p r e - d r i l l a p i l o t h o l e
/ the diameter of the screw. It makes driving easier
and prevents splitting of the workpiece.
8 ENGLISH