Tabla de contenido
Idiomas disponibles
Idiomas disponibles
6. Display and keyboard overview
For software user language selection, please see chapter 9.1
Rough filler
Program
Symbol for flash off
Remaining time in
1:48
current program mode
Arrow up to scroll up
Arrow down to scroll
down
I to start the heating
sequence
The temperature rise per
minute
Activated Curing program
Time flash off / Full bake
Rough filler
Flash off symbol
Full bake symbol
6
Trisk CureMaster 2 DTL
More information if
pressing enter
Chosen cassette/s
that will be active when
starting
Selection of cassettes
that will be active
NOTE: has to be done
before turning on the
lamps.
I
II
Enter button to get
access to change values
and confirm changed
values
0 to stop the machine
or cancel change of
parameters
End temperature
Flash off values
Full bake values
4
15
50
6
20
80
# 420878 Rev 1
7.
How to run Program mode
7.1 Switch on the power
Hedson Technologies AB
When you turn the main
Box 1530
SE-462 28 Vänersborg
switch to position 1, you will
Sweden
see Manufacturer, Program
www.hedson.se
Program version: ??
version and Machine type
Machine type: ??
for 2 seconds.
User defined program 1 to 10
Plastic parts
Clear coat
7.2 Choose program
Top coat
You have 8 predefined
Water base
Base coat
programs and 10 empty
Spray filler
programs for your settings.
Fine filler
Rough filler
7.3 Distance measure-
ment and laser pointer
Place the cassette so that
Rough filler
the laser pointer is accor-
Too far
ding to chapter 8.3. The
display indicates "ready",
Pyrometer
off ?
"too far" or "too close".
+
A buzzer will sound
accordingly. If necessary
adjust distance. Correct
distance is 60 cm. *)
Rough filler
7.4 Start drying
The remaining time
for the flash off is
1:48
displayed.
The sequence can be
stopped at any time
When the flash off is ready,
by pressing 0.
the program automatically
changes over to full bake
mode.
The window shows
the remaining time
Rough filler
for the full bake
sequence. The drying
sequence can be
stopped at any time
3:00
by pressing 0.
*) If it is not possible to
When drying sequence is
measure the distance the dis-
completed you will return to
play will show "Check dist.
the menu "Choose program".
man" , i.e.check the distance
Please see Chapter 7.2.
manually
# 420878 Rev 1
Trisk CureMaster 2 DTL
7.5 Changing program parameters
(only experienced users!)
Press the enter button for 5 seconds and the first param-
eter starts to flash. When flashing it is possible to change
the value with the arrrow buttons. Press enter again and
you can change the next value and so on. Press 0 to go
back without saving parameters. Press 1 to save values.
Examples are found in chapter 11.
User defined program 1 to 10
Plastic parts
Clear coat
Top coat
Water base
Base coat
Spray filler
Fine filler
Rough filler
4
15
50
6
20
80
7.6 Pyrometer off
When turning the pyrometer off the machine
will use fixed power levels as a machine without
+
pyrometer (temperature) control.
The menus 7.5 and 7.7 will change into the
menus found in chapter 7.8 and 7.9.
To turn the pyrometer on again, press first 0 and
then 1.
7.7 Information menu
On the display you can see
Tc (current temperature) and
Tr (requested temperature).
Rough filler
3:00
Tr
70 °C
40
Tc
50 °C
PL
5
Remaining
time in
current mode
Power Level in
current mode
Temperature
measured inside
the control box
7
Tabla de contenido
